Catalogs >
ASC >
ASC 4411LN / ASC 4415LN

ASC 4411LN / ASC 4415LN
3Pages

Catalog excerpts

MEMS Capacitive Accelerometer ► Uniaxial ► Ultra Low Noise (LN) ► High g-Range ► 4 Wire System ► Amplified Output ► Aluminium Housing /Stainless Steel Housing ► Made in Germany Features ► Range: ±2g to ±400g ► DC Response ► High Shock Resistance ► Gas Damped ► Excellent Bias and Scale Factor Stability ► Differential Mode Options ► Customised Cable Length ► Customised Connector ► TEDS Module Applications ► Structural Monitoring and Testing ► Endurance Testing ► Brake Test ► Vibration Monitoring ► Civil Engineering ► Modal Analysis ► Vehicle Testing ► Automotive Ride Quality & Comfort ► Railway Engineering ► Flutter Test Capacitive MEMS Technology The accelerometers are based on a capacitive MEMS technology and can be used in a low frequency response up from 0Hz. Inside the sensor element, the seismic mass is connected with two conductive capacitor plates. If the seismic mass oscillates between the two capacitor plates the capacitance will change. This capacitance change is converted via an ASIC (Application Specific Integrated Circuit) into an analog signal. Description The model ASC 4411LN is an uniaxial accelerometer based on capacitive technology. It is over a wide temperature range fully compensated and factory calibrated. The sensor has been developed specifically for measuring relatively small accelerations, as required in the aerospace or automotive sector, for example. Because capacitive technology is used, extremely small measuring ranges are possible. The amplified output is easy to use with a data acquisition unit. The signal is independent from the power between +8VDC to +30VDC. The package is hard anodized aluminium that is rugged for automotive, industrial and military applications. A very high flexible rugged cable provides a simple mounting. The ASC 4411LN is equipped as standard with 6m cable. It is a Low Noise version and has a better frequency response. Owing the lower noise the ASC 4411LN provides a higher resolution. The stainless steel package of the ASC 4415LN provides a high resistance to strong environmental influences. ASC GmbH ■ Advanced Sensors Calibration ■ Ledererstra&e 10 ■ 85276 Pfaffenhofen ■ Germany ■ Tel. +49 (0) 8441 786 547 -0 ■

Open the catalog to page 1

Typical Specifications DYNAMIC Range (±g) 2 5 10 25 50 100 200 400" ELECTRICAL Excitation voltage V DC 8-30 Zero acceleration output ±mV 150 150 80 80 80 80 80 80 Isolation Case Isolated Residual / Broadband noise (±5% frequency range) |jV 100 60 70 90 100 100 125 125 ENVIRONMENTAL Thermal sensitivity shift %/°C 0.015 Thermal zero shift mg/°C 0.15 0.4 0.75 2 4 7.5 15 30 Operating temperature range °C -40°C to +100°C Storage temperature range °C -55°C to +125°C...

Open the catalog to page 2

FACTORY CALIBRATION (SUPPLIED WITH THE SENSOR) Range 2g and 5g 10g 25g 50g and 100g 200g and 400g CALIBRATION DIN ISO 17025 (ORDER SEPARATELY) Range 2g and 5g 10g 25g 50g and 100g 200g and 400g Cable Code/Pin Configuration Red Supply + Black Supply -Green Signal + White Signal -ORDERING INFORMATION 4411LN 002 6 A Model number Range (Ex. 050 is 50g) Cable length (meters) Connector & Pinout ASC GmbH ■ Advanced Sensors Calibration LedererstraSe 10 ■ 85276 Pfaffenhofen ■ Germany ■ Tel. +49 (0) 8441 786 547 -0 ■ office@asc-sensors.de All data,...

Open the catalog to page 3