Efficient fixing for cracked concrete VERSIONS APPROVALS ▪ zinc-plated steel ▪ stainless steel ▪ highly corrosion-resistant steel BUILDING MATERIALS Approved for: ▪ Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: ▪ Concrete C12/15 ▪ Natural stone with dense structure ADVANTAGES APPLICATIONS FUNCTIONING ▪ The optimised expansion clip allows for a high load-bearing capacity. Thus fewer fixing points and smaller anchor plates are required. ▪ The international approvals guarantee maximum safety and the best performance. ▪ The bolt geometry allows for optimal load distribution and therefore enables use close to edges and in thin components. ▪ Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler installation. ▪ The drive-in pin protects the thread from damage and ensures a troublefree dismantling of the fixture. ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ High performance steel anchors Bolt anchor FAZ II ▪ The FAZ II is suitable for prepositioned and push-through installation; also suitable for stand-off installation under certain conditions. ▪ Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut). ▪ When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall. ▪ The head embossing offers a simple control of the anchoring. ▪ In the case of series installation, we recommend using the FABS anchor bolt setting tool. http://www.fischerwerke.de/en/ - 13/07/2012 Steel constructions Guard rails Consoles Ladders Cable conduits Machines Staircases Gates Façades Wood constructions 1

Article name FAZ II 12/50 A4 FAZ II 12/60 A4 FAZ II 12/100 A4 FAZ II 12/160 A4 FAZ II 16/25 A4 FAZ II 16/50 A4 FAZ II 16/100 A4 FAZ II 20/30 A4 FAZ II 20/60 A4 FAZ II 24/30 A4 FAZ II 24/60 A4 Art.-No. 501419 501420 501421 503180 501423 501424 501425 501426 503183 501427 503184 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Drill hole diameter Anchor length Max. fixture thickness do l t fix [mm] 12 12 12 12 16 16 16 20 20 24 24 [mm] 150 160 200 260 148 173 223 172 202 205 235 [mm] 50 60 100 160 25 50 100 30 60 30 60 Drill hole diameter Anchor length Max. fixture thickness do l t fix [mm] 8 8 10 10 12 12 16 16 [mm] 75...

Highest permissible loads for a single anchor11 in concrete C20/254: For the design the complete approval ETA - 05/0069 has to be considered 11 The partial safety factors for material resistance as regulated in the approval as well as a partial safety factor for load actions of y|_ = 1,4 are considered. As an single anchor counts e.g. an an- chor with a spacing s > 3 x hef and an edge distance c > 1,5 x hef. Accurate data see approval. Z) Minimum possible axial spacings resp. edge distance while reducing the permissible load for the minimum memberthickness (hm¡n Ê 2 x hef). The combination of...

Highest permissible loads for a single anchor11 in concrete C20/254: For the design the complete approval ETA - 05/0069 has to be considered 11 The partial safety factors for material resistance as regulated in the approval as well as a partial safety factor for load actions of Ji = 1,4 are considered. As an single anchor counts e.g. an an- chor with a spacing s > 3 x hef and an edge distance c > 1,5 x hef. Accurate data see approval. Z) Minimum possible axial spacings resp. edge distance while reducing the permissible load forthe minimum member thickness (hm¡n Ê 2 x hef). The combination of...