ARM050.500

Product catalog summary

Product Overview: The document describes the ARM050.500, a rotatable intermediate hinge module. It includes specifications for assembly and installation, highlighting the components and procedures required.

Specifications: The module requires 8x M6 x 30 bolts, M4 x 84x, and 8x J6.4 components. It complies with standards TS EN 50085-1 and TS EN IEC 61439-1.

Assembly Instructions:

Remove the yellow tape and place the gasket with the adhesive surface inside.
Insert the profile into the coupling as indicated by the arrows in the diagram.
Tighten the profile bolts using J6.4 (M6) and M6x30 bolts.
Position and assemble the covers and bolts as shown in the picture.

Installation Procedures:

Place the cable protection plastics as depicted in the visual guide.
Limit the module's right-left rotations using M6X10 bolts. The module has eight holes at equal intervals for this purpose.
Optionally, set rotation limits with two bolts.

Recommendations:

Check gaskets for high sealing to ensure proper installation.
Use M4x8 bolts for additional assembly tasks.

Critical Information: The document emphasizes the importance of correctly positioning components and securing them with the appropriate bolts to ensure functionality and compliance with specified standards.

Catalog excerpts

Rotatable Intermediate Hinge ( Ara Bağlantı Modülü ) ARM050.500 Sarı renkli bantı çıkarınız. Yapışkan yüzeyi içeri gelecek şekilde contayı yerleştiriniz. (Remove the yellow tape. Place the gasket with adhesive surface inside.) Proﬁli ok yönünde içeri doğru yerleştiriniz. ( Insert the proﬁle into the coupling as show

Open the catalog to page 1

Proﬁl cıvatalarını takınız. Proﬁli ok yönünde içeri doğru yerleştiriniz. ( Tighten the proﬁle bolts ) ( Insert the proﬁle into the coupling as shown in the picture below) Kablo koruma plastiklerini görseldeki gibi yerleştiriniz. ( Place the cable protection plastics as shown in the picture ) Proﬁl cıvatalarını takınız. ( Tighten the proﬁle bolts )

Open the catalog to page 2

Dikkat: Modülün sağ sol dönüşlerini M6X10 cıvata ile sınırlandırabilirsiniz. Modül üzerinde eşit aralıklarla sekiz adet delik bulunmaktadır. Dönüş sınırlarını isteğe bağlı olarak 2 adet cıvata ile de yapabilirsiniz. Sarı renkli bantı çıkarınız. Yapışkan yüzeyi içeri gelecek şekilde contayı yerleştiriniz. (Remove the yellow tape. Place the gasket with the adhesive surface inside) Attention: You can limit the right-left rotations of the module with M6X10 bolts. There are eight holes at equal intervals on the module. You can optionally set the rotation limits with two bolts M6 x 10 Dönüş Sınırlama...

Open the catalog to page 3

All ARMENDUS catalogs and technical brochures

ARM080.420
4 Pages
ARM080.820
2 Pages
ARM080.800
4 Pages
ARM080.710
4 Pages
ARM080.705
4 Pages
ARM080.700
4 Pages
ARM080.610
4 Pages
ARM080.505
4 Pages
ARM080.050
1 Page
ARM080.025
1 Page
ARM050.830
3 Pages
ARM.050.800
3 Pages
ARM050.710
4 Pages
ARM050.700
4 Pages
ARM050.610
4 Pages
ARM050.600
3 Pages
ARM050.400
4 Pages
ARM050.025
1 Page
ARM080.600
4 Pages
Support Arm and Enclosure System
13 Pages
Rotatable Panel 90° Angle Coupling
4 Pages

Archived catalogs

ARM050.420
3 Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list