AWH-TCG-ZR (Cleaning Technology)

Product catalog summary

Overview: The document is a technical data sheet for the Rotation Monitoring Sensor AWH-TCG-ZR by Armaturenwerk Hötensleben GmbH. It provides detailed specifications, operational guidelines, and installation instructions for the sensor used in monitoring rotating tank cleaning nozzles.

Specifications:

Electrical Data: Supply voltage is 24 V +/-20% (18 to 32 VDC), with power requirements of less than 20 mA. The output signal is PNP, 50 mA, short circuit-proof, and active. Start-up delay is less than 0.3 seconds, and response time is approximately 30 seconds.
Operating Conditions: Ambient temperature ranges from -10 to +60°C, storage temperature from -20 to +70°C, with a protection class of IP68. The operating pressure is a maximum of 10 bar, and the operating temperature is 0 to +100°C.
Materials: The G1/2'' nozzle is made of 1.4404, the probe tip of PEEK, the case of 1.4301/1.4305, and the O-ring of EPDM. The sensor weighs approximately 465 g.

Operational Guidelines:

Parameterization: The sensor must be electrically installed and connected to PC software for parameterization. The cleaning cycle should be recorded to adjust switching thresholds and output logic.
Analysis: A PLC can analyze the digital PNP output signal with a timer to determine the effectiveness of the cleaning cycle.

Installation Instructions:

Operation: Parameterization requires removing the cover and connecting the PC via an interface. The sensor is powered through an M12 plug.
Settings: Adjustable parameters include switching thresholds and output logic, which can be monitored and adjusted via PC software.

Warnings:

Operators must verify the sensor's functionality in various conditions and approve its application.
Condensation due to temperature changes can damage the sensor.
The IP68 classification does not guarantee suitability for applications below the dew point or thermal shock conditions.

Additional Information: The document includes contact information for Armaturenwerk Hötensleben GmbH and its global representatives.

Catalog excerpts

Armaturenwerk Hötensleben GmbH Data Sheet CIPGuard (TCG-ZR)

Open the catalog to page 1

Rotation Monitoring Sensor AWH-TCG-ZR Data Sheet

Open the catalog to page 2

Rotation Monitoring Sensor AWH-TCG-ZR Data Sheet Technical Data Electrical data Supply voltage: Ub = 24 V +/-20% 5 (18 to 32 VDC) Power requirements: < 20 mA 4 Output signal: PNP; 50 mA; short 1 circuit-proof; active Start-up delay: < 0,3 s Response time: approx. 30 sec Operating conditions Ambient temperature: Storage temperature: Protection class : Operating pressure: Operating temperature: 1 +VDC 2 Tx (to be contacted with programming adapter only) 3 3 GND 2 4 OUT/PNP 5 Rx (to be contacted with programming adapter only) G1/2'' nozzle: Probe tip: Case: O-ring: Weight: 1.4404 PEEK 1.4301/1.4305...

Open the catalog to page 3

Rotation Monitoring Sensor AWH-TCG-ZR Data Sheet Phase 1 - Start of cleaning process Phase 2 - Cleaning identified Phase 3 - Error, cleaning nozzel positioned directly on the sensor Phase 4 - End of cleaning process: measured value and dynamics drop out Picture 1 The cleaning starts in phase 1 at approx. 50 seconds. After another 20 seconds starts phase 2, in which the sensor recognizes a proper cleaning according to the set parameters (measured value and dynamics are within the switching thresholds). There is an error in the cleaning device in phase 3 (from approx. 200 to 250 seconds). The cleaning...

Open the catalog to page 4

Data Sheet Rotation Monitoring Sensor AWH-TCG-ZR 1. Measured value (blue) The measured value is proportional to the jet intensity of a cleaning device. The chart shows the rotating phases of a jet cleaner. The measured value contains a minimum and maximum value (switching thresholds). These switching thresholds of the measured value shall be adjusted that way, that the measured value lies within the switching thresholds at proper cleaning. 2. Dynamics (red) The dynamics is proportional to the frequency of the jet cycles. This means that a fast rotation of a jet cleaner with powerful spraying...

Open the catalog to page 5

Rotation Monitoring Sensor AWH-TCG-ZR Data Sheet 6. Installation instructions 6.1 Operation Parameterisation Cover is removed for parameterisation. The PC is connected with the aid of the interface and of the plug-in adapter with the sensor (contact strip). The power supply is connected to the sensor via M12-plug. The parameterisation can begin. After parameterisation the cable is removed and the cover closed. Installation Depending on the sensor type, the electrical connection has to be carried out directly through the terminal block on the electronics or through the built-in M12 plug. The 24...

Open the catalog to page 6

Armaturenwerk Hötensleben GmbH Schulstr. 5 - 6 D-39393 Hoetensleben Tel.: +49 39405 92-0 Fax: +49 39405 92-111 e-mail: [email protected] http://www.awh.eu NEUMO Ehrenberg Group Armaturenwerk Hötensleben GmbH (Germany) Gebr. Rieger GmbH & Co. KG (Germany) NEUMO GmbH & Co. KG (Germany) Damstahl GmbH & Co. KG (Germany) NEUMO UK Ltd. (United Kingdom) NEUMO GUS (Russia) NEUMO Polska Sp. z.o.o. (Poland) NEUMO GUS Kransodar (Russia) Damstahl AG (Switzerland) Dams VNE Corporation (USA) Herrli AG (Switzerland) He NEUMO-EGMO Spain SL (Spain) NEUMO VARGUS (China) NEUMO Representative Offices Vietnam AWH Vienna...

Open the catalog to page 8

All Armaturenwerk Hötensleben GmbH catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list