Suction Filters Tank top mounting • Connection up to GVA / -20 SAE • Nominal flow rate up to 45 l/min / 11.9 gpm Application To be installed in the suction line of the pumps of hydraulic systems resp. upstream of the charge pumps of hydrostatic drives. Performance features Protection against wear: By means of filter elements that even in full-flow filtration meet the highest demands regarding cleanliness classes. Protection against malfunction: By means of full-flow filtration in the system return, the pumps above all are protected from dirt particles remaining in the system after assembly, repairs, or which are generated by wear or enter the system from outside. Special features > Bypass valve (optionally): The location close to the suction inlet prevents dirt particles retained by the filter element from entering into the clean oil side. > Foot valve: When the screw-on cap is removed for maintenance, the foot valve closes automatically. This makes it possible to service the filter even if it is submerged below the oil level in a full tank. Filter elements Flow direction from center to outside. The star-shaped pleating of the filter material results in: > large filter surfaces > low pressure drop > high dirt-holding capacities > particularly long service intervals Filter maintenance By using a clogging indicator, the correct moment for maintenance is stated, what guarantees an optimum utilization of the filter life.

Materials Screw-on cap: Polyester, GF reinforced Filter head: Aluminum alloy Filter bowl: Polyamide, GF reinforced Seals: NBR (FPM on request) Filter media: EXAPOR®MAX 2 - inorganic multi-layer microfiber web Paper – cellulose web, impregnated with resin Accessories Electrical and / or optical clogging indicators are available on request. Dimensions and technical data see catalogue sheet 60.20. Characteristics Nominal flow rate Hydraulic fluids Up to 45 l/min / 11.9 gpm (see Selection Chart, column 2). The nominal flow rates indicated by ARGO-HYTOS are based on the following features: Mineral...

Diagrams ∆p-curves for complete filters in Selection Chart, column 3 D1 Pressure drop as a function of the flow volume at ν = 35 mm2/s / 162 SUS (0 = casing empty) Pressure drop as a function of the kinematic viscosity at nominal flow Filter fineness curves in Selection Chart, column 4 Dx Filtration ratio β as a function of particle size x obtained by the Multi-Pass-Test according to ISO 16889 The abbreviations represent the following β-values resp. finenesses: For EXAPOR®MAX 2 and Paper elements: Filtration ratio β for particles > x µm 16EX2 =β16(c) = 200 EXAPOR®MAX 2 30P =β30 (c) = 200 Paper...

1 Those values apply when used in hydrostatic drives. Instructions in catalogue sheet 10.310 have to be observed. 2 Versions with by-pass valve on request. All filters are delivered with a plugged clogging indicator connection G/. As clogging indicators either manometers or vacuum switches can be used. Optional extension pipes adapt the filter length to various tank depths. For ordering of accessories please use the below mentioned codes. Order example: The filter ES 075-6801 has to be supplied with an extension pipe (EV) for a mounting depth of 400 mm / 15.75 inch. Order description: ES 075-6801...

Groove for O-ring 126 x 4 mm / 4.96 x 0.16 inch O-ring part No. N007.1264 on request Design with 1 port Required mounting surface (Design with 2 ports on request) Connection G¼ for clogging indicator For calculation of dimension EV see selection chart Measurements in inch Type www.argo-hytos.com Subject to change · 10.35-EN/US · 0818

Spare Parts Pos. Designation Part No. 1 Screw-on cap with ES 074.1212 100 x 4 mm 3.94 x 0.16 inch 3 Replacement filter see Selection Chart / col. 10 element 4 O-ring N007.1264 126 x 4 mm* 4.96 x 0.16 inch* 5 Rubber ring ES 075.0109 *not included in basic equipment The functions of the complete filters as well as the outstanding features of the filter elements assured by ARGO-HYTOS can only be guaranteed if original ARGO-HYTOS spare parts are used. Quality management according to DIN EN ISO 9001 To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls...