across a wide variety of nutrition, health and industrial markets. SPX FLOW had approximately $1.4 billion in 2020 annual revenues and has operations in more than 30 countries and sales in more than 140 countries. To learn more about SPX FLOW, please visit www.spxflow.com.

The order code is constructed as follows: * Add multiple options to the end of code (i.e. -A1A3) SVS1 Intermediate Flanged (4-piece design) SVS2 Intermediate Flanges (4-piece design) New version (2) MATERIAL OF CONSTRUCTION 316L Housing Material (3) PORT CONNECTIONS F Hygienic Flange (SVS1 only) T Clamp (DIN 32676) W Buttweld G DIN Male Thread (DIN 11851) S SMS Swedish Milk Standard (SMS 1145) X Without Counter Flanges (SVS1 only) Mixed port connections only available for SV1, specify both key identifiers. Example: TS Additional port connections available upon request. Please contact factory....

(9) SEAL MATERIAL E EPDM (6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options. Use identifier "AA0A" as default for valves without control unit or sensor feedback. CU Identifier Positions 1 & 2 CONTROL UNIT TYPE *Only available on CU with AS-i communication **Only available on CU with Direct Connect Wire (8) SEAT TYPE TR Elastomeric Profile Seal

The order code is constructed as follows: (1) VALVE TYPE BLV1 2-way ball valve (2) MATERIAL OF CONSTRUCTION 316L Housing Material CONTROL UNIT TYPE

€> The order code is constructed as follows: 1 A, B & C sizes can be used beyond the nominal valve sizes DN25-DN100. See instruction manual for holding pressures. For change-over valves, "Normally Closed" = "Fail Down" and "Normally Open" = "Fail Up" Additional and mixed port connections available upon request on certain housing combinations. Please contact factory. Not available for large sizes DN 125, DN 150 and T60

(6) CONTROL UNIT / FEEDBACK S e e p a g e 3 1 fo r m o s t c o m m o n c o n t r o l u n i t c o n f i g u r a t i o n s. B O L D i n d i c a t e s s t a n d a rd c o n t ro l u n i t o p t i o n s. U s e i d e n t i f i e r “ H P 0 N ” a s d e f a u l t fo r v a l v e s w i t h o u t c o n t r o l u n i t . U s e i d e n t i f i e r “A A 0 A” fo r v a l ve s w i t h m a n u a l h a n d l e. INSIDE POLISH CU Identifier Positions 1 & 2 CONTROL UNIT T YPE C4 None 3.1 SPX FLOW Inspection certificate B1 3-A certification (at minimum with 0.8 µm (32 µ-in) Ra ID finish) Elastomer shaft seal For high...

SWmini Series Fractional Size Single Seat Valves The order code is constructed as follows: (6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options. Use identifier "HP0N" as default for valves without control unit. Use identifier "AA0A" for valves with manual handle. CONTROL UNIT TYPE Note: 3-A certified design is standard

The order code is constructed as follows: Add multiple options to the end of code (i.e. -A1A3) (1) VALVE TYPE MS Diaphragm Style with Metal Stem and Elastomeric Seat Seal MSP Diaphragm Style with PTFE Stem Add "L" to actuator identifier for stroke limiting mid-position actuator (example "B1L"). Only available on A1, B1, C1. 1 A, B & C sizes can be used beyond the nominal valve sizes DN25-DN100. See instruction manual for holding pressures. For change-over valves, "Normally Closed" = "Fail Down" and "Normally Open" = "Fail Up"

(6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options. Use identifier "HP0N" as default for valves without control unit. Use identifier "AA0A" for valves with manual handle. *Not available with MSP type CONTROL UNIT TYPE 1 9 3 *Not available with MSP type 1 Solenoid 1 Solenoid + NOT Element* 3 Solenoid B1 3-A certification (at minimum with 0.8 pm (32 p-in) Ra ID surface finish) C1 Shaft flush for large sizes *Only available on CU with AS-i communication **Only available on CU with Direct Connect Wire (8) SEAT TYPE TR...

AP Series Fractional Size Aseptic Diaphragm Single Seat Valves (1) VALVE TYPE AP Fractional Size Diaphragm Style with PTFE Stem (2) HOUSING COMBINATIONS Shut-off Valves (7) CONTROL UNIT / ACTUATOR CONNECTORS (3) PORT CONNECTIONS W Buttweld (8) SEAT TYPE PT PTFE Stem (9) SEAL MATERIAL T PTFE The order code is constructed as follows:

(1) VALVE TYPE D4 Double Seat Mix Proof Shut-off Valves *Not available with seat lift actuator COMMUNICATION TYPE (3) PORT CONNECTIONS W Buttweld (7) CONTROL UNIT / ACTUATOR CONNECTORS Additional and mixed port connections available upon request. Please contact factory. (6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options. Use identifier "HP0N" as default for valves without control unit. CU Identifier Positions 1 & 2 CONTROL UNIT TYPE (8) SEAT TYPE TR Elastomeric Profile Seal (9) SEAL MATERIAL E EPDM GLASS BLASTED OD...

The order code is constructed as follows: (1) VALVE TYPE DT4 Tank Outlet Mix Proof (2) HOUSING COMBINATIONS COMMUNICATION TYPE COMMUNICATION VOLTAGE (3) PORT CONNECTIONS W Buttweld Additional port connections available upon request. Please contact factory. (7) CONTROL UNIT / ACTUATOR CONNECTORS 6 MM AIR FITTINGS ELECTRICAL CONNECTION NOTE: Shaft flush and 3-A certified design as standard

The order code is constructed as follows: * Add multiple options to the end of code (i.e. -A1A3) (1) VALVE TYPE DA4 Advanced Ultra-Hygienic Double Seat Mix Proof (6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options. Use identifier "HP0N" as default for valves without control unit. CONTROL UNIT TYPE NOTE: 3-A certified design is standard

The order code is constructed as follows: E Add multiple options to the end of code (i.e. -A1A3) (1) VALVE TYPE DE Double Seat Mix Proof (2) HOUSING COMBINATIONS (7) CONTROL UNIT / ACTUATOR CONNECTORS (3) PORT CONNECTIONS W Buttweld *Only available on CU with AS-i communication **Only available on CU with Direct Connect Wire (8) SEAT TYPE TR Elastomeric Profile Seal Non Seat Lifting (Includes External Flush to clean atmospheric vent cavity) (9) SEAL MATERIAL E EPDM (6) CONTROL UNIT / FEEDBACK See page 31 for most common control unit configurations. BOLD indicates standard control unit options....