Our products
42Pages

Summary Duromat analyzers ………………………………………………………………………………………………………. 02 Chlorine dioxide …………………………………………………………………………………………………………… 24 Pilot distributors …………

Hardness analysis (total hardness, residual hardness) and alkalinity of the water (carbonic hardness, positive m value) (with graphic display) Colorimetric analyzer, with microprocessor for the control of water hardness with the following measuring ranges: measuring range (depends on the type of reagent) Water hardness (total and residual) Alkalinity (carbon hardness, positive m value) French degrees: 0.022 - 53.57 ° f French degrees: 0.54 - 40.2 ° f German degrees: 0.012 - 30 ° dH German degrees: 0.3 - 22.5 ° dH English degrees: 0.02 - 37.59 ° e ppm CaCO3: 0.22 - 534 ppm CaCO3 mmol / l:...

The analyser is complete with: 4 programmable relay outputs: maximum value one, maximum value two (or minimum value and maximum value), command for a cooler, for a washing valve, pump, error, missing indicator, remote signaling. 1 output 0 (4) -20mA: analysis result (linear hardness) and operation. 2 programmable digital inputs: water meter, turbine water meter (Hall), flow meter, external start or stop commands. MODBUS connection. CANBUS connection (optional). SD card connection: data / results / error saving and transfer with date and time, software update. A bad analysis can be repeated...

Available reagents (content 500ml): Art Water hardness measuring range (total hardness, residual hardness) °f °dH °e ppm mg/l mmol/l 0,022-0,21 0,04-0,36 0,05-0,54 0,11-1,07 0,16-1,61 0,27-2,68 Alkalinity measuring range (carbon hardness, positive m value) 200887 710/500 0,5-13,4 200889 715/500 0,8-20,5 200890 720/500 1,1-26,8 200891 730/500 1,6-40,2 (*) need for on-site calibration DUROMAT® professional Mounted in box 0,2 - 6 ate (2x104 – 6x105 Pa) DUROMAT® professional On a plate 0,2 - 6 ate (2x104 – 6x105 Pa) (reagent is not included) Water hardness (total hardness, residual hardness)...

Analysis of the amount of silica in water (with graphic display) Multifunctional microprocessor analyzer to analyse the amount of silica in the water. Possibility to program two alarm set points (pre-alarm and alarm). The DUROMAT® Diamond system controls the quality of the water; this allows to avoid problems or damages caused by the presence of Silica when a programmed threshold is exceeded. With display of the measurement result. 4 programmable relay outputs: max value 1, max. value 2 (or minimum and maximum value), control for: cooler, wash valve, pump, error, indicator failure or remote...

2 programmable digital inputs: water meter, turbine water meter (Hall), flow meter (start/stop), external start analysis or stand-by commands. SD card connection: saving and data/results/error transfer with date and time, remote software update. You can repeat a bad analysis as soon as the maximum value is exceeded, without giving an alarm signal (change of the status of the output relay). Extensive program of operation control, relay operation, Leeds drive, accessory control. Cycle of the analysis: opening of the inlet solenoid valve - washing of the measuring chamber for a set time -...

Range of measurement (*) Silica SiO2 200940 Silica, reagent A 0,3 until 10,0 mg/l 200941 Silica, reagent B 200942 Silica, reagent C 200945 Complete set 2 x A, 1 x B, 1 x C (*) using a dilution unit, the measuring range can be expanded. DUROMAT® Diamond 85 – 264V 47-63Hz (230V 50-60Hz) 0,2 - 6 ate (indicator excluded from delivery) 24V AC/DC 200194 Dilution unit to analyse higher values 0,2 - 6 ate Accessories (not needed for operation): Cleaning set Aerator, 230V 50-60Hz Cooler For road transport For air transport to eliminate CO2 in water for water temperatures from 40 up to 80 ° C for...

Hardness analysis (total hardness, residual hardness) and alkalinity of the water (carbon hardness, positive m value) (with graphic display) Multifunctional microprocessor analyser for the analysis of the amount of iron in water with measuring range: Measurement range (depends on the type of indicator) Water hardness (total and residual) Alkalinity (carbon hardness, positive m value) French degrees: 0,022 - 53,57 °f French degrees: 0,54 - 40,2 °f German degrees: 0,012 - 30°dH German degrees: 0,3 - 22,5 °dH English degrees: 0,02 - 37,59 °e ppm CaCO3: 0,22 - 534 ppm CaCO3 mmol/l: 0,002 - 5,3...

The analyser is complete with: display of the measured hardness result. 2 programmable relay outputs: maximum value, alarm and/or fault 1 0(4) -20mA output: result of the analysis (linear hardness) and operation 1 digital input: start analysis. SD card connection: data / results / error saving and transfer with date and time, software update. A bad analysis can be repeated (just exceeded the maximum value, without giving an alarm signal) Extensive program of operation control, relay drive, Leeds drive, accessory control. Steps of an analysis cycle: opening an inlet solenoid valve - washing...

Available reagents (content 500ml): Art Water hardness measuring range (total hardness, residual hardness) °f °dH °e ppm mg/l mmol/l 0,022-0,21 0,04-0,36 0,05-0,54 0,11-1,07 0,16-1,61 Alkalinity measuring range (carbon hardness, positive m value) 200887 200889 200890 200891 Water hardness (total hardness, residual hardness) Alkalinity (carbon hardness, positive m value) DUROMAT® IQ mounted on a plate Water hardness (total hardness, residual hardness) Alkalinity (carbon hardness, positive m value) 24V AC/DC 200142 Optional: Cleaning set Pressure reducer Sampling launch pump For road...