*mydirectindustry

CCG series

Product catalog summary

Description
The CCG series of annular/force washer load cells are designed for measuring compressive forces in various research and industrial applications. They are commonly used in electro-mechanical test rigs and critical bolted installations to monitor bolt tension profiles. Additionally, they are utilized in cable tension systems, typically at the cable anchor point. These load cells can be supplied with monitoring/control electronics and calibrated as a system.

Key Features

Capacities range from 12.5kN to 540kN
Sealed to IP66 for environmental protection
Low profile and compact design
Low deflection
Compatible with metric and imperial bolt sizes
Robust construction
3-year warranty

Options Available

Non-standard sizes upon request
Shunt calibration facility
Other ranges available upon request
Special mounting adaptors available upon request

Specifications

Rated Capacities: 12.5 to 540 kN
Sensitivity Range: 1.5 mV/V nominal
Non-Linearity: <1.5% typical / 5% worst-case
Repeatability: <5%
Zero Balance: <±1% for identical mounting position, <±10% for altered mounting position
Temperature Range: Operating -20 to +70°C, Compensated +10 to +60°C
Temperature Effect on Output: <0.030% of Rated Output/°C
Safe Overload: 150% of Rated Capacity
Ultimate Overload: 300% of Rated Capacity
Excitation: Recommended 10 Volts AC or DC, Maximum 15 Volts AC or DC
Input Impedance: 375 Ohms (750 for capacities above 40kN)
Output Impedance: 350 Ohms (700 for capacities above 40kN)
Insulation Impedance: >500 Megaohms
Construction: Stainless Steel
Cable: 2 Metre 4 Core PVC Screened

Dimensions
Dimensions are provided in millimeters for various ranges, indicating the diameter and height of the load cells.

Note
The sensitivity range is dependent on the mounting position. Maintaining the same position ensures repeatability and linearity within specified parameters. Altering the position may change sensitivity and repeatability by up to ±10%.

Catalog excerpts

Stainless Steel Annular/Force Washer Low Profile and Very Compact Suitable for use with Metric and Imperial Bolt Sizes Robust Construction Options Available Non-Standard sizes available on request Shunt Calibration Facility Other ranges available on request Special mounting adaptors available on request DESCRIPTION The CCG range of annular/force washer load cells has been designed for the measurement of compressive forces and theyare used in a wide range of research and industrial applications. The CCG is often used in electro-mechanical test rigs and other critical bolted installations for monitoring continuously or periodically the tension profile of bolts during their use in the installation. The CCG is also used in cable tension systems and usually positioned at the cable anchor point. The CCG, as with all other Applied Measurements sensors, can be supplied complete with monitoring/control electronics and calibrated as a system (please refer to the Instrumentation datasheets). Transducer Specialists... APPLIED MEASUREMENTS LIMITED 3 MERCURY HOUSE - CALLEVA PARK - ALDERMASTON - BERKSHIRE - RG7 8PN - UK Tel: (+44) 0118 981 7339 email: [email protected] Internet: www.appmeas.co.uk

Open the catalog to page 1

Wiring Schematic Diagram CHARACTERISTICS Rated Capacities: Sensitivity Range: Non-Linearity: Repeatability: Zero Balance: Temperature Range Operating: Compensated: Temperature Effect On Output: On Zero: Safe Overload: Ultimate Overload: Excitation Recommended: Maximum: Input Impedance: Output Impedance: Insulation Impedance: Construction: Environmental Protection: Cable: UNITS kN mV/V ±% of Rated Output ±% of Rated Output ±% of Rated Output °C °C ±% of Rated Output/ °C ±% of Rated Output/ °C % of Rated Capacity % of Rated Capacity Volts AC or DC Volts AC or DC Ohms (nominal) Ohms Megaohms Note...

Open the catalog to page 2

CCG series

CCG series

Catalog excerpts

All Applied Measurements catalogs and technical brochures