
OPERATION AND MAINTENANCE MANUAL Automatic Non-Carbon-Brush Series SAING EI CORP. http://www.mytorqtools.com Y2F212A-3-015
Open the catalog to page 1NOTICE Metal Assembly sensor screwdriver are designed for installing threaded fasteners in light industrial and appliance manufacturing applications. SAING EI CORP. is not responsible for customer modification of tools for applications on which SAING EI CORP. was not consulted. WARNING Important safety information enclosed. Read all these instructions before placing tool in service or operation this tool and save these instructions. It is the responsibility of the employer to place the information in this manual into the hands of the operator. Failure to observe the following warnings could result...
Open the catalog to page 2WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock fire and/or serious injury. The term “power tool” in all of the warning listed below refer to your mains operated (corded) power tool or battery operated (cordless) power tool. SAVE THIS INSTRUCTIONS a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmosphere, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust of fumes. c) Keep children, and bystanders...
Open the catalog to page 3d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are cause by poorly maintained power tools. Inspect...
Open the catalog to page 4Grounding Instructions 1、This tool should be grounded while in use to protect the operator from electric shock. NOTICE! To ensure the grounding result, the grounding conductor of the power cord must be well connected with the grounding terminal of power facility. This tool is equipped with grounding conductors. The Green (or Green and Yellow) conductor in the Power Cord is the grounding wire. Never connect Green (or Green and Yellow) to a live terminal. The grounding wires in this tool can not only earth the electric leakage safely, but also can eliminate ESD-the electrostatic that tool occurred...
Open the catalog to page 51) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketone, or other similar chemicals to come in contact with the sensor screwdriver housing as damage will result. 2) Use the sensor screwdriver carefully, do not drop or be impacted, it is best to use a balancer to lift it, and set it on the auxiliary arm for operation. 3) Loading and unloading the sensor driver head: Simply pull down the screwdriver head cap with your fingertips to freely attach or detach the sensor screwdriver head, release the finger to return the screwdriver head cap to fix the sensor screwdriver...
Open the catalog to page 6Function / Operating Introduction (3) 1) Start Mode: Set the start mode on the controller MODEL MY-SAVER 2) LED Lighting: Set tool lighting on the controller 4) Button Switch: Turn on and off the setting for screw removal, there will be no OK or NG signal action when screw removal is in action. It is recommended to set the direction on the controller first, before setting screw removal, which includes CW and CCW. Please refer to the following table for 9-level torque and speed setting. The torque to remove screw should be larger than that to fasten screw. For detailed controller setting, please...
Open the catalog to page 71. The recommended daily operating time for this transducerized screwdriver is no more than 8 hours to remain a better performance. Depending on usage frequency and tool load, it is recommended to apply lubricant to the clutch every 3 to 6 months. Calibration should be performed every one million cycles or at least once a year. For maintenance and calibration, please contact your local distributor. 2. Please note don’t let the motor get over heated, please refer to the Working Time from the Technical Specification sheet. 3. The frequency use of this electric sensor screwdriver is over than eight...
Open the catalog to page 81. The use of other than genuine MYTORQ replacement parts may Result in decreased tool performance and increased maintenance and may invalidate all warranties. 2. All repairs and maintenance of this tool and its word must be performed by an authorized service center. 3. SAING EI CORP. is not responsible for customer modification of tools for applications on which SAING EI CORP. was not consulted. 4. Repairs should be made only by authorized, trained personnel. Consult your nearest MYTORQ authorized service center. 5. It is the responsibility of the employer to place the information in this manual...
Open the catalog to page 9MY-SAVER3 with BIT MY-SAVER5 with BIT MY-SAVER7 with BIT 1.3~1.8mm screw 1.8~2.0mm screw 2.0~2.6mm screw 3.0~4.0mm screw
Open the catalog to page 10Specifications MODEL Power Consumption Repeatable Torque Accuracy Unloaded Rotation Speed ±3% (r/min) Can be set and adjusted Working Time Power controller MY-SAVER MEGA N-DAS Model of Suspension Rack Model of Side Handle Ass’y MY-SAVER W Type Not attached Socket. Our company reserves the right to modify the product without prior
Open the catalog to page 1116 Pages
10 Pages
10 Pages
14 Pages
7 Pages
10 Pages
8 Pages
8 Pages
18 Pages
10 Pages
21 Pages
49 Pages
29 Pages
8 Pages
2 Pages
18 Pages
35 Pages
32 Pages