MSP-600 600W AC/DC
5Pages

Catalog excerpts

600W Single Output Medical Type •Universal AC input / Full range •Built-in active PFC function, PF>0.94 •High efficiency up to 89% •Withstand 300VAC surge input for 5 seconds •Protections: Short circuit / Overload / Over voltage / Over temperature •Medical safety approved (MOOP level) •Built-in cooling fan ON-OFF control •Built-in DC OK signal •Built-in remote ON-OFF control •Standby 5V@0.3A •Built-in remote sense function •No load power consumption<0.8W (Note.7) •Current sharing up to 2400W (3+1) (24V,36V,48V) •5 years warranty SPECIFICATION MODEL RATED CURRENT CURRENT RANGE RATED POWER RIPPLE & NOISE (max.) Note.2 100mVp-p OUTPUT 2.8 ~ 3.8V VOLTAGE TOLERANCE Note.3 ±2.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME VOLTAGE RANGE Note.5 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE 5V STANDBY Earth leakage current < 300 A/264VAC , Touch leakage current < 100 A/264VAC μ μ 105 ~ 135% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 3.96 ~ 4.62V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down 5VSB : 5V@0.3A ; tolerance± 5%, ripple : 50mVp-p(max.) PSU turn on : 3.3 ~ 5.6V ; PSU turn off : 0 ~ 1V REMOTE CONTROL RC+ / RC-: 4 ~ 10V or open = power on ; 0 ~ 0.8V or short = power off WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve") 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃ , 10 ~ 95% RH TEMP. COEFFICIENT 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION PACKING NOTE All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Tolerance : includes set up tolerance, line regulation and load regulation. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) Derating may be needed under low input voltages. Please check the derating curve for more details. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. No load power consumption<0.8W when RC+ & RC- (CN100 pin3,4) 0 ~ 0.8V or short. When the input voltage is less than 40VAC, the SPS may exhibit degradation of performance. The final product manufacturers must re-confirm this deviation that does not affect basic safety or essential performance. File Name:MSP-600-SPEC 2013-12-30

Open the catalog to page 1

600W Single Output Medical Type Mechanical Specification AC Input Terminal Pin No. Assignment Pin No. 1 2 3 DC Output Terminal Pin No. Assignment Assignment AUXG AUX RC+ RCCS Assignment Mating Housing Terminal GND DC-OK HRS DF11-10DS HRS DF11-**SC +S or equivalent or equivalent -S Block Diagram PWM fosc : 70KHz AUX POWER ACTIVE INRUSH CURRENT LIMITING RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER DETECTION CIRCUIT Derating Curve CURRENT SHARING REMOTE CONTROL Output Derating VS Input Voltage 100

Open the catalog to page 2

600W Single Output Medical Type Function Description of CN100 Pin No. Function Description 1 AUXG Auxiliary voltage output ground. The signal return is isolated from the output terminals (+V & -V). Auxiliary voltage output, 4.75~5.25V, referenced to pin 1(AUXG). The maximum load current is 0.3A. This output has the built-in oring 2 AUX diodes and is not controlled by the "remote ON/OFF control". 3 4 5 6,8 7 9 10 Turns the output on and off by electrical or dry contact between pin 4 (RC-), Short: Power OFF, Open: Power ON. Remote control ground. Current sharing signal. When units are...

Open the catalog to page 3

600W Single Output Medical Type 3.Remote Control The PSU can be turned ON/OFF by using the "Remote Control" function. Between RC+(pin3) and RC-(pin4) Output Status 4.Current Sharing with Remote Sensing (Only for 24V, 36V and 48V) MSP-600 has the built-in active current sharing function and can be connected in parallel to provide higher output power : (1)Parallel operation is available by connecting the units shown as below. (+S,-S,CS and GND are connected mutually in parallel). (2)Difference of output voltages among parallel units should be less than 2%. (3)The total output current must not...

Open the catalog to page 4

We are here for you. Addresses and Contacts Sales Switzerland & Liechtenstein Sales International Key Accounts Matthias Rüegg Ruhbergstrasse 32 CH-9230 Flawil Peter Felder Thurgauerstrasse 66 CH-8052 Zürich Sales Austria Sales Germany Postcode 10000 –59999 Postcode 80000 –99999 Kurt Stritzelberger Neumarkter Str. 86a D-81673 Munich Dieter Hirthe Auf der Entenweide 4 69502 Hemsbach Kurt Stritzelberger Neumarkter Str. 86a D-81673 Munich Sales Other Countries / Product Management Sensors Power Supplies Physical Sensors Data Acquisition DC-DC Converters Switching Power Supplies DC-AC Inverters...

Open the catalog to page 5

MSP-600 600W AC/DC 5Pages

Catalog excerpts

All Angst+Pfister Sensors and Power AG catalogs and technical brochures

MSP-600 600W AC/DC
5Pages