Catalog excerpts
ANGLgear ® right angle drives Inch and Metric Series “The Original Right Angle Gear Drive” Made in the U.S.A.
Open the catalog to page 1INDEX Intro to ANGLgear Inch & Metric Series 2 Flange Units, Inch Series pg. 4 3 Flange Units, Inch Series pg. 5 Selection & Ordering Information, Inch Series pg. 6 2 Flange Units, Metric Series pg. 7 3 Flange Units, Metric Series pg. 8 Selection & Ordering Information, Metric Series pg. 9 Special Units Inch & Metric Series 1 pg. 2-3 pg. 10 800-713-6170 • www.andantex.com • info@andantex.com
Open the catalog to page 2INTRODUCTION The Original Right-Angle Gear Drive The ANGLgear line of bevel gearboxes has proven its performance for over 40 years. It was developed to provide manual or power transmission of rotary motion in a compact, standardized right-angle unit. Each ANGLgear is manufactured at our factory in Wanamassa, NJ, USA. All units are inspected and tested to ensure proper operation at the rated speeds. The ANGLgear name is widely recognized and the product is in use worldwide. We also offer a line of metric ANGLgears for use in designs needing metric shaft diameters and mounting surfaces....
Open the catalog to page 3ANGLgear Quality Specifications: BEVEL GEARS All gears in the ANGLgear product line are cut using the Gleason Generating System to a AGMA Quality Class 9. This system develops straight bevel Coniflex tooth profiles, which are crowned at the center of the tooth. This allows for better tooth meshing, and operating pitchline velocities of over 1000 feet per minute. All gears are then carburized case hardened to ensure a long operating life. BEARINGS There are four ball bearings in each ANGLgear unit. Each bearing is packed with Exxon Beacon 325 Grease and sealed with two Buna-N seals. The...
Open the catalog to page 4SELECTION & ORDERING INFORMATION, INCH SERIES SERVICE FACTORS Selection Procedure 1. Determine the output speed and torque required for your application. The maximum recommended output speed is 3000 rpm for 1:1 units, and 1500 rpm for 2:1 units. 2:1 units are NOT recommended for use as speed increasers. 2. Select an application service factor from the chart to the right. Multiply your torque by the selected service factor. If you are unsure of the factor to be used, please consult us. 3. Using the chart below, find your output speed on the left. If your speed is not shown, use the next...
Open the catalog to page 7SPECIAL UNITS The photo above shows examples of special units that Andantex USA has designed/modified to meet our customers’ requirements. We will design/modify any unit to meet your design specifications. Special models can be provided with: - - - - - - Various shaft lengths and configurations. Same relative rotation of input-to-output shafts (BO) 3-way units with counter-rotating output shafts. Shafts with flats, splines, holes, etc. Modifications to the mounting flanges and housing. Special materials, bearings, seals, greases, coatings, etc. Service & Replacement Parts All units can be...
Open the catalog to page 111705 Valley Road • Wanamassa, NJ 07712 Phone: 800.713.6170 • 732.493.2812 • Fax: 732.493.2949 • E-mail: info@andantex.com • www.andantex.com
Open the catalog to page 12All Andantex USA Inc catalogs and technical brochures
-
MODULAR RACK & PINION SYSTEM
4 Pages
-
Full Bridge Spec
2 Pages
-
KRP
4 Pages
-
Linear & Rotary
119 Pages
-
Planetary Gearboxes Catalogue
14 Pages
-
Andantex product catalog
12 Pages