Full Bridge Spec

Product catalog summary

Mounting Options: The document outlines various mounting options for the Andantex Full Bridge Cartridge Dead Shaft Idler Roller Load Cells, including standard, flange, or pillow block configurations.

Specifications:

Electrical: The load cells require a 5 VDC excitation and provide a 500 mV nominal output at full load. The gauge resistance ranges from 80 to 130Ω, and the type is semi-conductor. Non-repeatability is ±1/4% full span, and combined non-linearity and hysteresis are ±1/2% full span.
Connector: The load cells use a male 4-pin M12 connector with specific pin assignments for excitation and signal.
Load Rating: Available in sizes 75, 100, 150, and 250 lbs, with overload tested at 300% of the rated load and overload stops at 110% of full load.
Environmental: Classified as IP54, with an operating temperature range of -4 to +150°F (-20 to +70°C) and a temperature coefficient of 0.02% per degree.
Mechanical: Deflection ranges from 0.008 to 0.015 inches (0.203 to 0.381 mm), with a maximum alignment of 1°. The bore size is 1½ inches (40 mm), with bushings available for smaller shafts.
Finish: Constructed from stainless steel.

Features & Benefits:

Higher sensitivity for superior accuracy.
Equipped with an M12 connector and full bridge 500mV voltage output.
Stainless steel construction with dustproof IP54 rating.
Mechanical variance compensation for shaft expansion and misalignment.
360° overload protection.

Part Numbers: The document lists part numbers for various load cell configurations and M12 cables, including straight and 90° connectors in different lengths.

Additional Information: For different bore sizes, contact the sales department. The document also provides contact information for Andantex.

Catalog excerpts

Andantex Full Bridge Cartridge Dead Shaft Idler Roller Load cells Mounting Options: Features & Benefits:  Higher sensitivity for superior accuracy  M12 Connector  Full Bridge 500mV Voltage output  Multiple Mounting options Standard, flange or pillow block  Stainless Steel Construction  Dust proof (IP54) rating.  Mechanical Variance Compensation For shaft expansion & misalignment  360° overload protection Specifications Electrical Excitation ……………………………………………………………. 5 VDC Output ……………………………. 500 mV, nominal @ full Load Gauge Resistance………………………………….. 80 to 130Ω Type…………………………………… Semi‐Conductor Non‐Repeatability…………………………………. ±1/4% full span Non‐Linearity and Hysteresis (combined) ±1/2% full Span Connector Type …………………………………………………….. Male 4 pin M12 Pin 1 ……………………………………………………………… Excitation Pin 2 ……………………………………………………………………. Signal Pin 3 ……………………………………………………………………. Signal Pin 4 ………………………………………………………………. Excitation Load Rating – lb. (N) Size 1………………………………………….…75, 1

Open the catalog to page 1

Full Bridge Wiring Diagram: Size 1 Cartridge load cells (Stud mount) Dimension: M10‐1.5x10 Size 1 Full Bridge Cartridge load cells part Number: Description Part Number Full Bridge Size 1 – MWF 50lbs Side Connector Bore 1.5” Full Bridge Size 1 ‐ MWF 75lbs Side Connector Bore 1.5” Full Bridge Size 1 ‐ MWF 100lbs Side Connector Bore 1.5” Full Bridge Size 1 ‐ MWF 150lbs Side Connector Bore 1.5” Full Bridge Size 1 ‐ MWF 250lbs Side Connector Bore 1.5” M12 Cables: Description Part Number M12 Super Shield Cable Straight Connector 6 meters (20’) P/N: 950.100.06 M12SSCSC06 M12 Super Shield Cable 90° Connector...

Open the catalog to page 2

Full Bridge Spec

Full Bridge Spec

Catalog excerpts

All Andantex USA Inc catalogs and technical brochures