Industrial catalogue
28Pages

ANACONDA FLEXIBLE METAL HOSE CORRUGATED HOSE STAINLESS STEEL : BW656-BW856-BW956 MONEL : BW673 BRONZE : BW794

COMPANY PROFILE. Anamet Europe BV is a specialist in the eld of exible connection and protection systems. As a part of Anamet Inc., we can support customers with our specialism all over the world. We offer our customers solutions to questions of connecting and protecting cables, pipes and hoses. Anamet offers metal hoses for the transport of liquids and gases together with accessory items for thermal insulation and fastening. Anamet can provide custom designed products to meet specic customer requirements. QUALITY ASSURANCE POLICY. Through the implementation of our ISO 9001 quality...

ANACONDA FLEXIBLE METAL HOSE CONTENT Introduction: company prole & quality assurance policy Engineering data ANACONDA CORRUGATED METAL HOSE SYSTEMS Type BW 656 Stainless Steel AISI 316L, Standard Pressure Type BW 856 Stainless Steel AISI 316L, High Pressure Type BW 956 Stainless Steel AISI 316L, Extra High Pressure Type BW 673 Monel . Type BW 794 Bronze Standard end-connections for the BW series Anamet Europe B.V. refrains from any liability for products produced, assembled or modied by other parties and/or improper use or mis-usage from data mentioned in this catalog. All claims resulting...

ANACONDA METAL HOSE ANACONDA METAL HOSE CORRUGATED METAL HOSE INTRODUCTION INTRODUCTION ANACONDA metal hose is the leader in the exible hose eld since our beginning in 1908. ANACONDA stands for a complete line of exible products, such as corrugated metal hose, stripwound hose, metal bellows and expansion joints, vibration eliminators, Sealtite electrical wiring conduit, and specially designed exible connectors for many purposes. Our leadership in the eld was made possible by years of dedication to producing only the highest quality metal hose products available. Strict quality control...

ENGINEERING DATA QUALITY ASSURANCE Within ANAMET EUROPE B.V. quality assurance is integrated in the corporate philosophy and adopted by all levels of the company. ANAMET EUROPE B.V. is since May 28th, 2002 certied by “Stoomwezen B.V.” to produce exible hoses accordingly to the Pressure Equipment Directive (PED) 97/23/EG, even up to category II. The objective of the company’s Quality Assurance Programme is to attain a quality level conform to ISO-9001. In addition to the requirements and specications of the end-users ANAMET produces in conformity with international regulary standards of...

ENGINEERING DATA ENGINEERING DATA HOSE ASSEMBLY DESIGN CONSIDERATIONS HOSE ASSEMBLY DESIGN CONSIDERATIONS Flow velocity Safety factor Extremely high conveyant velocities in corrugated hose should be avoided as the corrugations could be forced into resonant vibration resulting in premature fatigue failure. Consult your ANAMET representative for applications involving ow velocities in excess of 35 m/s for braided hose and 6 m/s for unbraided hose. We suggest that the maximum working pressures be no more than 25% of the rated burst pressure of the hose assembly after correcting for service...

ENGINEERING DATA IMPORTANT POINTS WHEN INSTALLING HOSE ASSEMBLIES RIGHT AXIAL LOAD Axial compression may lead to squirm the corrugated hose. Axial tension lowers the pressure capacity of braided hose. BENDING Install a hose in its most natural loop. Overbending lowers the pressure capacity and the cycle life WEIGHT The weight of the hose and the medium must be supported adequately. TORSION Torsion must be avoided. Torsion occurs when the movements are not in the same plane as the ttings. INSTRUCTIONS FOR SELECTION, INSTALLATION AND MOUNTING The life time of metal hoses will increase when...

ENGINEERING DATA DETERMINING MINIMUM OVERALL LENGTH OF HOSE ASSEMBLIES FOR INTERMITTENT FLEXURE From the “minimum c/l bend radius for exing bend” column in the hose specications, obtain the proper bend radius for the type and size of hose chosen. Use the formulas below to calculate the length “A” of the exposed hose required. Determine the overall length of ttings from tting specication pages and add to the exposed length of hose “A” to arrive at the assembly overall length. Distance between end connections should be such that there is no stress on the hose in the extreme offset position....

ENGINEERING DATA VERTICAL LOOP FOR MAXIMUM VERTICAL TRAVEL The illustration at the right shows the proper method of installing hose in vertical loops. The formula and the table for “B” will aid in determining the overall length of an assembly. Example A = 230 x 2 = 460 mm (2x “minimum c/l bend radius for exing bend”, see table type BW856). B = 410 mm (from table “B”) S = 200 mm (desired movement) Overall length= Using 25 mm type BW856-1H hose with ttings attached. VERTICAL LOOP FOR SHORT HORIZONTAL TRAVEL The formula and the table for “B” will aid in determining the overall length for an...

ENGINEERING DATA MISALIGNMENT AND OFFSET MOVEMENTS For intermittent offset movement consult offset formula on page 9 and the “minimum c/l bend radius for exing bend” columns in specications for each type and size of corrugated hose. For misalignment and ease of instal- lation where there is no signicant movement or vibration, consult offset formula on page 9 and “minimum c/l bend radius for permanent bend” columns in specications for each type and size of corrugated hose. MUTIPLE MOVEMENTS To absorb movements in several directions and at several planes, a 90° exible hose assembly is...

ENGINEERING DATA CORROSION RESISTANCE TABLE The following tables may be used only as a guide in the selection of the most suitable hose and tting material when conveying a given medium. The listed media are in general considered to be pure, at room temperature and, unless otherwise specied, dry. A change in any one of these conditions may change the rating. No attempt has been made to account for variations in service conditions since these variables are too innumerable and complex. Additional information on service life, etc. is keyed to the fol- RATING CODE lowing notes. The numbers...