USB Type-C™ Power Delivery v3.0 Controller with De-Mux (USB/DP) ANX7327 is a USB-PD v3.0 port controller with an integrated de-mux that supports switching at data rates of up to 10Gbps. ANX7327 supports high-speed interfaces, such as USB 3.1 (Gen 1 – 5Gbps, Gen 2 – 10Gbps) and DisplayPort™ (DP) 1.4 at up to HBR3 (8.1Gbps). ANX7327 is designed to be placed behind a USB Type-C (USB-C™) receptacle of a USB-C accessory or HDTV or monitor USB-C port. The USB-C port with the embedded IC device behind it enables a passive USB-C cable connectivity between any USB-C source and the accessory or HDTV or monitor to further the USB-C functions to a display or data connectivity downstream. On the source side, when paired with a re-timer mux such as the ANX7440, the ANX7327/7440 combo solution can enable a USB-C full function port with CPUs that have integrated USB-C mux. An Onchip Microcontroller (OCM) is available to manage the signal switching, Channel Configuration (CC) detection, USB Power Delivery (USB-PD) charging and Vendor Defined Message (VDM) protocol, and other functions, as defined in the USB Type-C v1.2 and USB Power Delivery v3.0 specifications. ANX7327 can be configured for an Upstream Facing Port (UFP) to support a USB-C receptacle. When paired with a DP-to-HDMI/VGA bridge (such as the ANX7737/9837), the ANX7327 creates an ideal solution for USB Type-C dongle, docking, HDTV, and monitor applications. High-speed de-mux (4x6) switching up to 10Gbps USB 3.1 signal output (SSTX and SSRX) with Gen1 (5Gbps) and Gen2 (10Gbps) link speed Native TCPC-compliant hardware register interface Dedicated control signals for VBUS Source FET, VBUS sink FET, and VBUS auto discharge circuity Serial and debug interfaces DisplayPort Alternate Mode (SlimPort®) communication support through USB-PD structured VDM messaging Integrated VCONN FETs Built-in 10-bit ADC to monitor VBUS voltage and current Industry standard compatibility − − − − USB Type-C r1.2 specification USB Power Delivery v3.0 r1.0 specification DisplayPort 1.4 specification DisplayPort Alternate Mode over USB Type-C r1.1 specification − Universal Serial Bus (USB) Type-C Port Controller Interface r1.0 specification Low-power design − Single supply at 3.3V − Dedicated supply power pin for flexible I/O power – 1.8V or 3.3V − Ultra-low power consumption (typical 80uW) in standby mode 4-lanes DisplayPort outputs with link speed of 1.62Gbps, 2.7Gbps, 5.4Gbps, 6.75Gbps, and 8.1Gbps On-chip Microcontroller (OCM) to implement signal switching, USB-PD messaging, and DisplayPort related functions − 64K bytes SRAM for firmware execution − 128K bytes Flash for firmware storage − PDFU function for firmware updating Dead battery detection support Package offered: 48-pin QFN, 6mm x 6mm, 0.90mm Z-height, pin-pitch: 0.4mm Applications USB Type-C dongle, docking, HDTV, monitor DP Lane 0 TCPCcompliant registers I2C Slave Embedded Flash GPIOs/Ext. Mux & FET controls I2C Master Cable Det. & Orientation VBUS Detection ANX7327 USB 2.0 signals will be routed externally of

Product Brief Related Products Part Number Copyright ©2018 Analogix Semiconductor, Inc. 3211 Scott Blvd., Suite 100 Santa Clara, CA 95054, USA +1 (408) 988-8848 ©2018 Analogix Semiconductor, Inc. All Rights reserved. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS” WITHOUT ANY EXPRESS REPRESENTATIONS OF WARRANTIES. IN ADDITION, ANALOGIX SEMICONDUCTOR INC. DISCLAIMS ALL IMPLIED REPRESENTATIONS AND WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTURAL PROPERTY RIGHTS. This document contains proprietary...