Group: AMETEK
Catalog excerpts
MT Series - Série MT Tension/Compression Mechanical Test Stand Bancs d’essais de traction & compression User Manual - Manuel d’utilisation MT Series User Manual
Open the catalog to page 1PRODUCT WARRANTY This instrument is warranted against defects in workmanship, material and design for one (1) year from date of delivery to the extent that AMETEK will, at its sole option, repair or replace the instrument or any part thereof which is defective, provided, however, that this warranty shall not apply to instruments subjected to tampering or abuse, or exposed to highly corrosive conditions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED AND AMETEK HEREBY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF FITNESS FOR A...
Open the catalog to page 25.0 Compression Testing Procedure... 10 5.0 Procedure de Test en Compression... 26
Open the catalog to page 31.0 INTRODUCTION The CHATILLON MT test stand is designed to perform various tension or compression tests utilizing the full range of CHATILLON force gauges. The MT test stand has two available capacities 150 LBF (660 N) and 500 LBF (2.2 KN). Each capacity has a quick-action lever or precision hand-wheel operating mechanism available. The MT test stand can be positioned vertically and mounted to a bench or wall mounted. The MT test stand can also be horizontally mounted and fastened to a bench. The wall mounting and horizontal mounting utilize the same components. The MT column comes in...
Open the catalog to page 43.2 Force Gauge Mounting Kits When ordering a force gauge mounting kit the parts shown in FIGURE 1 will be supplied as indicated. For DFE2/DFS2/DFX2 Series Gauges use SPK-MT-0001 mounting kit from 0 to 150 LBF testing and use SPK-MT-0004 mounting kit for 150 to 500 LBF testing. MT Series User Manual
Open the catalog to page 5The ruler assembly instructions are as follows: 3.3.1 Assemble CROSS BEAM (Item 1) to top of lever or hand-wheel assembly of MT test stand using two SCREWS (Item 9). 3.3.2 Assemble MTG PLATE (Item 2) to CROSS BEAM (Item 1) using two SCREWS (Item 9). 3.3.3 Thread RULER ROD (Item 5) to ROD HOLDER (Item 6). 3.3.4 Assemble ROD HOLDER (Item 6) to MTG PLATE (Item 2) using two SCREWS (Item 8). 3.3.5 Press on RULER ASSEMBLY (Item 4) to RULER ROD (Item 5). 3.3.6 Assemble POINTER ARM (Item 7) to movable RACK on MT test stand using 5/16-18 ADAPTER (Item 3). The pointer arm should be located in front...
Open the catalog to page 63.4 Digital Indicator Assembly Kit The digital indicator assembly instructions are as follows: 3.4.1 Assemble CROSS BEAM (Item 1) to top of lever or hand-wheel assembly of MT test stand using two SCREWS (Item 8). 3.4.2 Assemble MTG PLATE (Item 2) to CROSS BEAM (Item 1) using two SCREWS (Item 8). 3.4.3 Assemble ACTUATOR ARM (Item 4) to the lower two screw holes of the DIGITAL INDICATOR (Item 6) using two SCREWS (Item 7). 3.4.4 Assemble DIGITAL INDICATOR (Item 6) to MTG PLATE (Item 2) using two SCREWS (Item 5). 3.4.5 Assemble ACTUATOR ARM (Item 4) to movable RACK on MT teststand using 5/16-18...
Open the catalog to page 73.5 Horizontal / Wall Mounting Kit The Horizontal/Wall mounting assembly instructions are as follows: 3.5.1 Remove top plastic cap from top of column using a small screw driver. 3.5.2 Assemble two SCREWS (Item 3) to MTG PLATE (Item 2) and thread on two LONG NUTS (Item 1). 3.5.3 Slide bottom mounting plate assembly to lower part of the MT test stand column and fully tighten two screws using a 6mm hex key. 3.5.4 Repeat step 3.5.2 for the top mounting plate assembly. 3.5.5 Slide top mounting plate assembly to upper part of the MT test stand column and fully tighten two screws using a 6mm hex...
Open the catalog to page 83.6 Additional Spare Parts 3.6.1. Load Actuation Assemblies SPK-MT-L150 Lever Actuation Model, 150 LB/660 N SPK-MT-L500 Lever Actuation Model, 500 LB/2.2 KN SPK-MT-H150 Hand Wheel Actuation Model, 150 LB/660 N SPK-MT-H500 Hand Wheel Actuation Model, 500 LB/2.2 KN 3.6.2. Miscellaneous Spare Parts SPK-MT-REMOTE Remote load cell MTG kit (0.55 LB/250 G to 200 LB/890 N) SPK-MT-REM500 Remote load cell MTG kit (500 LB/2.2 KN) 4.0 STANDARD ACCESSORIES The Standard accessories that come with the MT test stand are as follows: NC000714 Hex Key, 6mm NC002660 Operation Manual SPK-FMG-012B Hook Assembly,...
Open the catalog to page 95.0 COMPRESSION TESTING PROCEDURE 5.1. Establish the platform location in reference to its travel so that the deflection requirements for the test to be made will be accomplished before the platform reaches the limit of its stroke. For example: if the test requires 2 inches of deflection, ensure the platform will travel the required 2 inches before stopping. Allow additional travel for the deflection of the force gauge. Center the test specimen on platform and adjust height of force gauge above platform to desired height using the 6mm hex key provided. If deflection measurements using the...
Open the catalog to page 106.0 TENSION TESTING PROCEDURE 6.1. Establish the platform location in reference to its travel so that the deflection requirements for the test to be made will be accomplished before the platform reaches the limit of its stroke. For example: if the test requires 2 inches of deflection, ensure the platform will travel the required 2 inches before stopping. Allow additional travel for the deflection of the force gauge. Place test specimen in upper grip or hook and zero the force gauge. Then attach test specimen to lower grip or hook. If deflection measurements using the ruler assembly are...
Open the catalog to page 11MT Series User Manual
Open the catalog to page 12MT Series User Manual
Open the catalog to page 13MT Series User Manual
Open the catalog to page 14MT Series User Manual
Open the catalog to page 15MT Series User Manual
Open the catalog to page 16MT Series User Manual
Open the catalog to page 17MT Series User Manual
Open the catalog to page 18MT Series User Manual
Open the catalog to page 19FRANÇAIS 1.0 INTRODUCTION Le banc de test CHATILLON de la série MT est étudié pour réaliser une variété de tests de compression ou traction avec les différents dynamomètres de la gamme CHATILLON. Deux versions du banc de test MT sont disponibles : 660 N (150LBF) et 2.5 KN (500LBF). Chacune de ces versions peut être équipée d’un levier ou d’une manivelle. Les bancs de test MT peuvent être positionnés verticalement, sur un établi ou fixés à un mur. Ils peuvent être également disposés horizontalement sur un établi. Les montages muraux ou horizontaux utilisent les mêmes accessoires. Les...
Open the catalog to page 20All AMETEK Test catalogs and technical brochures
-
CS2
8 Pages
-
MT500 Series
2 Pages
-
LD Series
3 Pages
-
LR150K Plus
2 Pages
-
LR100K Plus
2 Pages
-
Pneumatic Testers
2 Pages
-
DMG Series
3 Pages
-
MSE100 Series
3 Pages
-
LG Series
2 Pages
-
DG Series
3 Pages
-
FORCE MEASUREMENT INSTRUMENTS
44 Pages
-
LS100 Series
2 Pages
-
LR10K Plus
2 Pages
-
LTCM100
3 Pages
-
MT150
2 Pages
-
TT
2 Pages
-
Model 332
3 Pages
-
Model 329
3 Pages
-
MSE100
3 Pages
-
DG
3 Pages
-
DFE II
4 Pages
-
XP2i Digital Pressure Gauge
8 Pages
-
M1 Digital Test Gauge
4 Pages
-
LR50KPlus Material Tester
2 Pages
-
LR30KPlus Material Tester
2 Pages
-
LR10KPlus Material Tester
2 Pages
-
LR5KPlus Material Tester
2 Pages
-
TA1 Texture Analyzer
4 Pages
-
LS1 Material Teste
4 Pages
-
Pneumatic Grips
3 Pages
-
Chuck & Collet Grips
4 Pages
-
Melt Flow Indexer MFI-9
2 Pages
-
Melt Flow Indexer MFI-10
2 Pages
-
Polymer Test Instruments
4 Pages
-
Ball Probes
10 Pages
-
Thermal Cabinets
2 Pages
-
FT1 Friction Tester
4 Pages
-
New TA Catalogue
24 Pages
Archived catalogs
-
Melt flow indexers
2 Pages
-
Density Gradient Columns
2 Pages