Remote programming andcollection of measurement data > Simulation of power levels up to54kW > Power level simulation up to 162KW for Three-Phase Operation A single chassis includes a 1500VA voltage source with 270V output (optional 312V L-N) and a 200 A Current Source, which is derived from exactly the same master oscillator as the voltage source. This means that the voltage and current outputs are at precisely the same frequency, although the phase relationship between the two may be varied to simulate different load power factors. > Monitors load parameters withoutadditional instrumentation > Whether the application is powersimulation or just AC current, the FX Series provides a very wide range of controllable constant current output from 20 mA to 200 A. The currentsource section features three ranges to ensure good resolution at low current settings. In fact, the 2 A range is usable down to 20 mA. The 20 A to 200A output is available via bus bar outputs, whereas outputs below 20 A are available at the rear panel barrier strip. > With the combined voltage andcurrent source in a single compact chassis, the FX Series is the ideal choice for the simulation of high power levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwattsto 54kW single phase or 162 kW three-phase and provides a universal system for both manual and programmable control applications. > For either two or three phasesystems, additional chassis are added. The individual oscillators are clocked from a single master, with a phase lock to ensure phase angle integrity. In multi-phase systems, the phase angle of the voltage may be varied independently as well as the phase angle between the voltageand current source for each phase. The system can simulate two or three-phase outputs with a different P.F. on each phase. This is extremely important when evaluating measurement or control scenarios for multi-phase systems with unbalanced loads. >

Connectors: Input provided on rear terminal block(TB-1)Output provided on rear terminal block(TB-2) (voltage & low output current)Bus Bars (high output current) > Front Panel Indicators: Power Over temperature Overload High Range Analog Volt Meter Input Circuit Breaker > Note: Remote Sense Mating Connectorsare provided Mechanical: Height:10.5 In. (26.7 cm) Width:19 In. (48.3 cm)Depth:23 In. (58.4 cm) Weight:165Lbs (75 kg) > Phase Angle: Control: Frequency: > Front Panel Controls- Circuit BreakerKeypad- 959XP TypeBus- IEEE-488.1Subsets- SH1, AH1, T6, L3, SR1, R12, DC1, DT1Data Transfer Rate- 200...

UTPUT R > ANGES : Standard 0-270 V. All voltagesare L-N. For other voltage ranges, please contact Factory.Standard: 20.1 - 200 Amps. Allcurrent levels are rms.Standard: 0.020 - 20 Amps. Allcurrent levels are rms. A > CCURACY :* TRMS Sense: 0.135V from 5V to 135V. ѱ0.54V from 135V to 270V. All at 25Cб1C (Based on TRMS reading)Calibrates to б0.02 Amps atfive cardinal points within range.a) Calibrates to 0.002 Ampson 2-20 Amp range (5pts) b) Calibrates to ѱ0.0002 Amps on 0.02-2 Amps range (6 pts) L > OAD R > EGULATION : TRMS Sense: 0.05% FS,no load to full load.ѱ0.05% FS0.05% FS L > INE R > EGULATION...

OPTION DESCRIPTION Complete 200 Amps Single Phase Systemconsisting of: (1)1500VA Voltage Source 0-270V, L-N (1)1500VA Current Source 20-200A (1)400VA Current Source 0.020-20A -UPInput Voltage for 4500FX(342-456V, L-L) -1P/20 -3P/2020 Amp Output Maximum(remove 20-200A Current Source) > Complete 200 Amps Three Phase System consisting of: (3)4500FX-1P/200 Units, Phase Lockedtogether -HVHigh Voltage Output on Voltage Channel(0-312V, L-N) NOTE: Initialization values of: When ordering, please specify: բȒ Voltage Output − Frequency > 9689 Towne Centre Drive, San Diego CA, 92121-1964(858) 677-9040FAX...