Model IPS
4Pages

{{requestButtons}}

Catalog excerpts

Model IPS - 1

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model IPS Semiconductor Gas Indicating Pressure Switch DESCRIPTION The IPS Indicating Pressure Switch is designed to provide economical pressure monitoring with setpoint indication of the high purity, toxic and corrosive gases used in the semiconductor manufacturing industry. ●● Operates low voltage audible/visual alarms and relays In addition to providing accurate (±2% of span) indication of gas pressure, this 2 inch diameter instrument incorporates a magnetically actuated, hermetically sealed reed switch capable of operating low voltage annunciators, lights or relays. When used with the appropriate pull-up or pull-down resistors, the monitor can be connected to the input port of a microprocessor or to a logic network. It may also be used as an input to a programmable controller. Moving the index on the front dial to the desired set point sets the switch. A small magnet fastened to the indicating pointer actuates the switch. A magnetic latch on the switch permits the switch to remain “on” or “off” after the pointer passes the operating point, without restraint on the indicating pointer. The switch action is configurable to close on increasing pressure (HA) or close on decreasing pressure (LA). In both models, the user can change the switch action by removing the front bezel, loosening the pointer screw, and flipping the pointer over. The switch action will be noted on the tail of the pointer. ●● No switch input power required ●● Provides input to logic networks, microprocessors and PLCs ●● Intrinsically safe apparatus when connected to approved barrier ●● Available in low mount and center-back mount configuration ●● Available with face seal fittings, tube stub or NPT connections ●● Switch setpoint adjustments accessible from front of monitor ●● Switch setting may be adjusted on or off-line ●● User selectable switch action ●● Type 316L stainless steel internal surfaces ●● 10 Ra surface finish on face seal connections ●● Polished stainless steel outer case and window ring ●● Helium leak tested to 10-9 scc/sec ●● Cleaned and packaged for high purity gas applications, exceeds ANSI B40.1 ●● Immune to EMI fields The IPS Pressure Switch offers the ease of adjustment and economy that permits field use of several units covering a variety of pressure range set-points. It is also a low cost alternative to analog transducers with A/D conversion for digital input to PLCs and microprocessors. The IPS Pressure Switch provides many advantages over other instruments, including: fast, easy, accurate setting of set points; pressure and setpoint indication on the same dial face; quick, at a glance monitoring of the pressure and setpoint, and substantial cost savings to the end user. Model IPS Semiconductor Gas Indicating Pressure Switch Sales/Technical Support Telephone: +1 215-355-6900 or e-mail: mctpmt.sales@ametek.com 820 Pennsylvania Boulevard | Feasterville, PA 19053 U.S.A. | Order Fax: +1 215-354-1802 © 2015, by AMETEK, Inc. All rights reserved. Printed in the U.S.A. K796432 – Effective: 6-2015, Supersedes: New (110130) Specifications are subject to change without notice. Visit

Open the catalog to page 1
Model IPS - 2

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model IPS Semiconductor Gas Indicating Pressure Switch SPECIFICATIONS Mechanical Size: 2 inch diameter Ranges (PSI or BAR): Connection: 26 AWG, Teflon® insulated, 10 foot leads; IPS-200 (2 black wires) Maximum Power: 10 watts DC, 12 VA AC Maximum Switching Current: 0.5 amps AC/DC noninductive (consult factory when using for inductive loads such as relays) VAC-0-200 psi, VAC-0-300 psi Note: VAC = 30 inches Hg vacuum Maximum Switch Voltage: 28 V AC/DC Gauge Pressure: 0 to 60, 100, 200, 300, 600, 1000, 2000, 3000, and 4000 psi; dual scales...

Open the catalog to page 2
Model IPS - 3

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model IPS Semiconductor Gas Indicating Pressure Switch Low Mount 1.36 (34.5) PRESSURE RELIEF GROMMET Swivel Female Face Seal Center Back Mount Ø 2.18 (55.4) 1.29 (32.9) METAL PRESSURE RELIEF FLAPPER Swivel Female Face Seal Fixed Male Face Seal Sales/Technical Support Telephone: +1 215-355-6900 or e-mail: mctpmt.sales@ametek.com 820 Pennsylvania Boulevard | Feasterville, PA 19053 U.S.A. | Order Fax: +1 215-354-1802 © 2015, by AMETEK, Inc. All rights reserved. Printed in the U.S.A. K796432 – Effective: 6-2015, Supersedes: New (110130)...

Open the catalog to page 3
Model IPS - 4

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model IPS Semiconductor Gas Indicating Pressure Switch Model Numbering: IPS Gas indicating pressure switch IPS Indicating pressure switch Setpoints 200 Single Switch action LA Closes on decreasing pressure HA Closes on increasing pressure Pressure ranges 0060 0100 0200 0300 0600 1000 2000 3000 4000 V to 0 to 30 V to 0 to 60 V to 0 to 100 V to 0 to 200 V to 0 to 300 0 to 60 psi 0 to 100 psi 0 to 200 psi 0 to 300 psi 0 to 600 psi 0 to 1000 psi 0 to 2000 psi 0 to 3000 psi 0 to 4000 psi Compound (Vac to 30 psig) Compound (Vac to 60 psig)...

Open the catalog to page 4

All AMETEK PMT Products catalogs and technical brochures

  1. 1981

    4 Pages

  2. Model 40

    9 Pages

  3. Model 742

    2 Pages

  4. Model 742 D

    3 Pages

  5. Model 89

    2 Pages

  6. Model 89D

    2 Pages

  7. Model-DCT

    5 Pages

  8. Model 88C

    3 Pages

  9. PMT LMA

    3 Pages

  10. L serie

    2 Pages

  11. Model LMA

    3 Pages

  12. ECPT10

    2 Pages

  13. Model IDT

    5 Pages

  14. PST360

    2 Pages

  15. Model 656

    5 Pages

  16. 1535 Gauge

    2 Pages

Archived catalogs