9000N Series Automatic Brinell Hardness Tester
4Pages

{{requestButtons}}

Catalog excerpts

9000N Series Automatic Brinell Hardness Tester - 1

NEWAGE® 9000N Series Automatic Brinell Testing System Specification Sheet The NEWAGE® 9000N Series makes a Brinell impression in conformance with the standard method for Brinell testing as described in ASTM E-10. The impression made with the 9000N Series is measured based on the the depth of the indentation as described in ASTM E-103. This technique offers higher productivity, faster testing and reduced operator influence. Like the Rockwell hardness method, the depth measurement used by the 9000N Series is calculated based on the difference in penetration depth between the preload (minor load) and the major load position. During a test sequence, the 9000N Series applies a preload, zeroes the measurement, applies a full load, returns to the preload setting, and calculates the depth measurement. An LVDT is used to measure the depth while a precision load cell is used to accuratey and precisely apply the loads. For a given material, the depth measurement has been established to be linear to the width of the indention, however this relationship may change due to material characteristics such as elastic recovery. Also, the ridge that is created and that forms around the impression may be higher on some materials, thus the width may vary. In order to compensate for this conditions, the 9000N Series may be programmed to adjust its readout so that the measurement accurately reflects the linear relationship of width and depth. The compensation is determined by “benchmarking” the impression by first using an optical measurement and comparing the measurement to the 9000N Series displayed result. The 9000N Series is comprised of a load frame, precision load cell sensor, LVDT for deflection measurement, hydraulic actuation system and our advanced electronics console. The 9000N Series performs all testing in the HB30 scale with a 10mm carbide ball and a 3000 kgf major load. Meets ASTM E-10 and E-103 Easy-to-use and Comprehensive Display Console Hi/Lo Tolerance Settings Adjustable Time @ Load Test Result Memory for up to 5000 results Split Memory RS232 Output Print and Display Statistics - Average - Range - Min/Max - Standard Deviation - CPk Sequence Numbering Lot Numbering Operation: Load Measurement: Load Selection (kgf): Time-at-Load (sec): Vertical Capacities with Elevating Screw: without Elevating Screw: Indenter Stroke: Indenter: Scale: Operating Temp: Warranty: Quality Assured. Visit us on the worldwide web: www.hardnesstesters.com Shown: 9000N Series without hydraulic power system. Hardness Testing

Open the catalog to page 1
9000N Series Automatic Brinell Hardness Tester - 2

The 9000N Series conform to ASTM E-103. Electronics Consoles advanced electronics console. The LED display displays prompts that guide you through the setup process. The display also indicates the result, scale, and SPC results. The advanced keypad has a numeric keypad, function keypad and scale select keypad. Function keys include MODE (set/view timed load, minimum thickness calculation and automatic averaging); STAT (view statistics, clear results, view/change sequence number, view/change lot number, split memory); TOL (view/change HI/LO tolerance setpoints); CAL (calculate/clear...

Open the catalog to page 2
9000N Series Automatic Brinell Hardness Tester - 3

Brinell files can be created and named, e.g. HB1, HB2, etc. Each file can be setup to have its own tolerance and evaluated independent of other files. RS232 Output The RS232 output on the 9000N Series can be used to print histograms or interface with a personal computer with our DataView™ application software for advanced data management and analysis. The 9000N Series can be configured to print totals, graphs, history, results/values only, and optionally X-bar and R charts. Totals When totals is configured, the 9000N Series will print SPC values for the hardness result sin memory. This...

Open the catalog to page 3
9000N Series Automatic Brinell Hardness Tester - 4

Ordering 9000 Series Model Standard Digital Bench Brinell (Base Unit only) Accessories and Options Part No. Indenter, 10mm tungsten carbide Penetrator shroud assembly, with swivel mount Washer, for nosepiece penetrator shroud, plastic Light, flexibler arm test point for illumination Bench cabinet, metal, for tester only Pocket Brinell scope, 20X, fixed focus with carrying case HiLight Brinell scope, 20X, adjustable focus with carrying case, 0.1mm resolution (special order) HiLight Brinell scope, 20X, adjustable focus with carrying case, 0.5mm resolution The Newage® 5620 Series HiLight...

Open the catalog to page 4

All Ametek Newage Testing Instruments catalogs and technical brochures

  1. MS-ZH Series

    6 Pages

  2. Pocket Scope

    2 Pages

  3. KB Series

    2 Pages

  4. ME-2 Series

    4 Pages