Thermometer Mountings & Accessories
16Pages

System 4 Thermometer Mountings and Accessories

THERMOMETER MOUNTINGS AND ACCESSORIES The Standard Bodied and Fibroptic range of temperature measurement systems from Land Infrared include a comprehensive range of thermometer mounting and protection accessories to suit any measurement environment. All mountings and accessories enable quick and tool-free installation and removal of the thermometer. The range of accessories can be sub-divided into three groups INDUSTRIAL, NON-HOSTILE and LABORATORY. These groups provide a classification which equate to the given environmental conditions. SELECTING MOUNTINGS AND ACCESSORIES The following...

CoMPlETE STANDARD BoDIED THERMoMETER SYSTEMS Optional Air Inlet Adaptor Sighting Tube Mounting Plate NoN-HoSTIlE Water-cooled Flange Thermometer Mounting Shoe Target Mounting Adapter Light Purge Large Ball Mounting lABoRAToRY Thermometer To Processor Small Ball Mounting

Mounting Plate O/N/AF* (Pt Nº 095.168) Note The O/N/AF Mounting Plate must not be used with either silicon carbide or sillimanite sighting tubes, or any sighting tubes with outside diameter greater than 57mm Sighting Tube STO or STC (STC shown) Sighting Tube STO or STC (STO shown) Air Purge S4 P (Pt Nº 091.561) Air/Water Inlet/Outlets Optional Air Inlet Adaptor 1"BSP to 10mm P/N 150.786) Large Ball Mounting S4 LB (Pt Nº 030.566)

THERMoMETER CoolING JACKET, END CAP AND PURGE Cooling Jacket S4 - J (Pt Nº 091.560) The cooling jacket contains an effective air or water cooling facility for use in environments where excessive heat may damage or affect the thermometer. The thermometer fits inside and is held in place by two retaining clips. Water cooled: Flow < 1 I/min (exceeding the recommended flow may cause over-cooling leading to condensation problems) Air cooled: Flow < 450 I/min Maximum working pressure: 700kNm2/7Bar (100psi) Plain pipe connections: ø9.5 Weight: 2.2kg The End Cap provides full environmental...

THERMoMETER MoUNTINGS AND BRACKETS Mounting Plate o/N/M (Pt Nº 095.091) The mounting plate has four fixing holes, three studs for the jacket or purge, and a centre thermometer hole. It is ideal for mounting System 4 thermometer systems. 4 holes Ø14 Weight: 1.55kg on 10 PCD Adjustable Mounting Plate o/N/AF (Pt Nº 095.168) The jacket or purge fastens to a circular plate, which with the adjustment of four screws can move up to 7.5° with respect to the main plate. For use where accurate sighting is essential. Weight: 5.0kg This plate is not suitable for use with either silicon carbide or...

WINDoW ASSEMBlY AND SIGHTING TUBES Sighting Tube Information Sighting Tubes Sighting tubes are made from metal or refractory materials and are either open ended (Type STO) or closed (Type STC). Type STO tubes are used when viewing a solid target through flame, smoke, fumes etc. The closed end of the type STC tube is used as the target. A thermometer used with an STC tube can replace a sheathed thermocouple. To attach the sighting tubes to a mounting plate a steel adapter (Type STA) is cemented into refractory sighting tubes. The STA is drilled to fit the studs on the mounting plate (O/N/M)....

Water Inlets/Outlets Air Inlet Mounting Shoe S4 MB (Pt Nº 029.226) Waterg Cooled Flange S4 WF (Pt Nº 029.547) Light Purge S4 LP (Pt Nº 091.811) Mounting Adapter S4 MA (Pt Nº 029.264) Mounting Plate S4 MP (Pt Nº 029.263) Large Ball Mounting S4 LB (Pt Nº 030.566) THERMoMETER MoUNTINGS AND ACCESSoRIES Mounting Shoe S4 MB (Pt Nº 029.226) The thermometer is held inside the Mounting Shoe using retaining clips similar to those on the S4 J jacket. The holes on the front permit mounting of the S4 LP purge or S4 WF flange. 3 holes Ø4.5 equispaced as shown on 78.6 PCD C Mounting Options A Mounting...

Water cooled flange S4 WF (Pt. No. 029.547) When the ball mounting is used with the mounting shoe (S4 MB), this adapter provides a stable plate on which to attach the shoe. Some applications do not require the strong physical protection and high efficiency cooling of the S4 J jacket, but some cooling may still be necessary to protect the thermometer. In these circumstances the water-cooled flange is recommended. It is mounted to the front face of the mounting shoe, and will ensure that the internal temperature of the thermometer does not exceed the recommended operating temperature upper...

lABoRAToRY Thermometer Small Ball Mounting S4 B (Pt Nº 150.560) Mounting Adapter S4 MA (Pt Nº 029.264) Large Ball Mounting S4 LB (Pt Nº 030.566) THERMoMETER MoUNTINGS AND ACCESSoRIES Mounting Adapter S4 MA (Pt Nº 029.264) When the ball mounting is used with the thermometer this adapter fits to the thermometer base (A) using the screws provided, and couples using the centre hole (B) to the Large Ball Mounting (S4 LB). Two ¼in BSW , ½in long r/head screws (112.467) are supplied with the adapter to secure it to the thermometer. 2 Holes CSK Ø10.5 large Ball Mounting S4 lB (Pt Nº 030.566) The...

Optic Head Optic Head Optic Head Existing System 3 Mountings Large Ball Mount S4 LB (Pt Nº 030.566) Fibroptic Angle Bracket S4 FB (Pt Nº 029.224) Optic Head Small Ball Mounting S4 B (Pt Nº 150.560) Adapter, Air Purge & Mounting Bracket (Pt Nº 029.873) Adapter, Air Purge & Mounting Plate (Pt Nº 029.872) Hinged Adjustable Mounting Plate (Pt Nº 028.745) Optic Head Light Guide Adapter, Air Purge & Mounting Plate Detector Module Adapter, Air Purge & Adjustable Mounting Flange (Pt Nº 029.871) Large Ball Mount S4 LB (Pt Nº 030.566) CoMPlETE FIBRoPTIC THERMoMETER

INDUSTRIAl Quick Release Adapter, Air Purge & Adjustable Mounting Flange (Pt Nº 029.871) The adapter, air purge and adjustable mounting flange assembly attaches to the optic head, and provides a mounting using the four holes through the circular plate. Three studs link the main plate to a smaller plate which provide adjustment to ensure accurate alignment on to the target surface; particularly useful when sighting onto a small target. The quick-release adapter which forms an integral part of this assembly allows rapid, no tools removal of the optic head for routine maintenance. Air purge...