950MD Gemco LDT
1Pages

1080 N. Crooks Road • Clawson, MI 48017 • 800.635.0289 • 248.435.0700 • Fax 248.435.8120 • www.ametekapt.com 17 950MD Note 1: Guide tube support brackets are supplied as standard for strokes of 72” or greater. Note 2: Special high temperature, abrasion resistant and oil resistant cables are available. Consult your Customer Service Representative. Accessories Item Part Number Vortex Cooler 04578009 Muf er for Cooler 04578010 Replacement 1/2” Spherical Rod End 04570140 Guide Tube Support Bracket (See note 1) C0903400 Replacement (Male Connector) for Option “C2” Connector 04521407 Female Mating Connector for Option “C2” Connector 04521372 Replacement (Male Connector) for Option “C3” Connector 04521568 950MD Compatibility Guide 940 Yes 950IS Consult Factory 951 Yes (Must be ordered w/2” Null Zone & 5” Dead Band) 952 Yes (Must be ordered w/2” Null Zone & 5” Dead Band) 953 Yes (Must be ordered w/2” Null Zone & 5” Dead Band) 955 See 956 Section 7330 Consult Factory 950MD Mill-Duty Housing 950 LDT Cable Assemblies Item Part Number Cable Assembly with Mate for Option “C” Connector Style, 6 Feet, (For 950-CP) SD0436700L6 Cable Assembly with Mate for Option “C” Connector Style, 6 Feet, (For 950A/950TP) SD0436000L6 951, 952 and 953 LDT Cable Assemblies Item Part Number Cable Assembly with Mate for Option “C2” Connector Style, 6 Feet SD0439700L6 5 Pin, Straight, Stainless Steel Cable Assembly with Mate for Option “C3” Connector Style, 6 Feet 949013L6 6 Pin, Straight, Stainless Steel Cable Assembly with Mate for Option “C4” Connector Style, 6 Feet 949032L6 Part Numbering 950MD 12A 0B Fully Retracted Overstroke in Inches Insert length of retract overstroke in inches followed by “B”. If no retract overstroke is required, simply insert “0B”. 0C X X Connector X Standard 1/2 inch NPT conduit tting (It is suggested to order a quick disconnect connector on the LDT) C MS Style Connector and Mate on Side of Housing (for 950 LDT) C2 Environmental MS connector and mate on side of housing (specify the Gemco LDT to be used within the body of the order; if the housing is being used with a competitive probe, please contact a Customer Service Representative at 800.635.0289) C3 5 Pin, 12mm, Euro Connector on Side of Housing (for 952A w/connector option S only) C4 6 Pin, 12mm, Euro Connector on Side of Housing (for 953D and SSI w/connector option S only) NC No Head Cover on the 950MD Housing W Special Head cover for LDTs using a water cooled jacket. Allows entry and exit of water lines. NOTE: This option does not support connector option C, C2 or C3. Options X None V Vortex air cooler B1 Protective boot - neoprene coated nylon (-60F to +250F ) B2 Protective boot - silicone coated fiberglass (-100F to +550F ) B3 Protective boot - teflon coated fiberglass (-100F to +500F ) R Rear mount spherical rod end 3/4” F Front mount spherical rod end 3/4” RS Stainless steel rear mount spherical rod end 3/4” with 304 stainless steel mounting bolt FS Stainless steel front mount spherical rod end 3/4” with 304 stainless steel mounting bolt L Deirin liner for extended life cycle on longer horizontal applications (used to protect the LDT’s rod assembly) SB 304 stainless steel boot Active Stroke in Inches Determine the “active” stroke to be measured followed by “A”. Fully Extended Overstroke in Inches Insert length of extend overstroke in inches followed by “C” If no extend overstroke is required insert “0C”