video corpo

Universal IV ™ CM Model
8Pages

{{requestButtons}}

Catalog excerpts

Universal IV ™ CM Model - 1

DATA SHEET Universal IV ™ CM Model Applications Automatic Well Testing (AWT) Lease Automatic Custody Transfer (LACT) Basic Sediment and Water (BS & W) Separation Vessels Pipeline Slug Detection Truck Unloading Pump Protection Dielectric Analysis Machinery Lube Oil Monitoring Durability Our Perm-A-Seal sensing element does not require epoxy coatings that wear out and require expensive servicing. There are no gaskets that require servicing and the sensing element is robust in well fluids that include large amounts of sand. Use the Best For over 50 years, Drexelbrook has established itself as the world's leader in capacitive based water cut measurements. We have done this by providing reliable and accurate products at a reasonable cost. We offer the highest pressure and temperature ratings in the industry. Our probes can handle pressures up to 1500 PSI and temperatures up to 450°F. Easy Configuration - Now with Built-in LCD Display and Keypad All Universal IV CM comes from the factory precalibrated and requires only one point validation. Field configuration can be done from anywhere along the two-wire loop with our HRTWin PC Software. You can also configure via local display / keypad without the need for laptop or handheld communicators. Worldwide Approvals The Universal IV CM Model has been approved for Class I, Div1, and Zone 0 hazardous locations. FM, FMc, ATEX, as well as IECEx approvals are available. Eliminate Routine Maintenance The Universal IV CM (Cut Monitor) is built upon the Drexelbrook expertise in RF Admittance that allows the electronics to ignore paraffin and other coatings that buildup on the probe. No need to take apart spool pieces and tie-off large pipelines. The Universal IV CM can be configured for NPT or flanged mountings and can be installed in common pipe diameters. 0-50% in Light Oil & 0-80% in Heavy Oil The Universal IV CM comes factory pre-calibrated to one of 11 pre-set ranges, for Light Oil (API Gravity > 25) and Heavy Oil (API Gravity < 25) Cote Shield™ The proven Cote-Shield is designed into the Universal IV CM series and enables the instrument to ignore a pre-determined length of the sensing element. The ability to ignore a pre-determined length allows the sensing element to extend into the fluid beyond the nozzle mounting, and possible pipe elbows, which can affect the measurement. The Cote-Shield™ puts the sensing area of the insertion probe directly into the process stream and guarantees a more representative sample of the emulsion. AMETEK’ DREXELBROOK www.Drexelbrook.com

Open the catalog to page 1
Universal IV ™ CM Model - 2

Analytical Products Operating Principle The method of using RF Admittance to measure water cut is widely successful because of the large difference between the dielectric constants of oil (k ˜ 2.3) and water (k ˜ 80). The sensing element and the ˜ ˜ pipe wall form the necessary two surfaces of the concentric capacitor. The system electronics transmit a radio frequency voltage to the sensing element that measures changes in capacitance. As the amount of water in the flowing oil increases, the net dielectric of the fluid increases which causes the capacitance to increase. The onboard...

Open the catalog to page 2
Universal IV ™ CM Model - 3

Sensing Element Selection The Universal IV™ Cut Monitor sensing element is selected based on pipe size, wetted parts, NACE requirement and pressure/temperature. Pipe sizes of 8" or larger or in tank installations require a concentric shield as well. Below is a selection guide of the standard sensing elements with 3-terminal connection and Cote-Shield™. * PEEK is a high temperature thermoplastic with characteristics similar to TFE but with far better abrasion resistance. PEEK is compatible with the same materials as 316 SS; except for sulfuric acid, methyl ethyl ketone, concentrated phenol,...

Open the catalog to page 3
Universal IV ™ CM Model - 4

Sensing Element Sizing The Cut Monitor sensing element varies with pipe size. The larger the pipe diameter size, the longer the sensing element active length must be. The Cote-Shield length is sized so the sensing element is fully extended into the fluid beyond nozzles and elbows. Below are some standard look up tables. Sensing Element Dimensions

Open the catalog to page 4
Universal IV ™ CM Model - 5

Analytical Products Integral Mounting / Dimensions - inches (mm) SENSING ELEMENT DEPENDENT Remote Mounting / Dimensions - inches (mm) SENSING ELEMENT DEPENDENT

Open the catalog to page 5
Universal IV ™ CM Model - 6

Technology RF Admittance / Capacitance Process Pressure Up 103 bar (1,500 psi), probe dependent Supply Voltage 13-30VDC, 2-wire loop powered Process Connection NPT, ANSI, and more upon request Ouput/Digital Protocol 4-20mA, HART Compatible with HART® Accuracy and Resolution Water Cut Nominal Water Cut Water Cut Integral or Remote Configuration 25 ft max cable length for remote configuration Response Time 350 msec nominal (no damping applied) 1-90 seconds programmable damping time Supply Voltage Effect 0.2% of full scale max Temperature Effect 0.5% per 100°F (37.7°C) change Start-Up...

Open the catalog to page 6
Universal IV ™ CM Model - 7

Measurement Type / Frequency and Phasing C0 Water Cut Monitor Electronics Digital Protocols 1 HART® Electrical Connection 0 3/4" NPT without external ground lug 1 M20 with external ground lug 2 3/4" NPT with external ground lug Surge / Noise Suppression 0 No additional filtering required 1 Signal filtering RFI and Surge protection (Integral or Remote) 2 Probe RFI (Remote only) 3 Signal filtering and Probe RFI (Remote only) 4 Probe HDSP (Heavy Duty Spark Protector) - Remote only 5 Signal filtering and Probe HDSP (Remote only) 6 Probe RFI and Probe HDSP (Remote only) 7 Signal...

Open the catalog to page 7
Universal IV ™ CM Model - 8

Process gland wetted part (X) B 316/316L SS Process connection (XX) A0 3/4" NPT B0 1" NPT BA 1" 150# RF Carbon Steel BB 1" 150# RF 316/316L Stainless Steel CB 1" 300# RF 316/316L Stainless Steel BD 1" 150# RF 316/316L SS TFE C2 1 1/2" Tri-Clamp E2 2" Tri-Clamp FA 2" 150# RF Carbon Steel FB 2" 150# RF 316/316L Stainless Steel GB 2" 300# RF 316/316L Stainless Steel FC 2" 150# RF CS TFE Face FD 2" 150# RF 316/316L SS TFE FE 2" 150# RF CS Inserted TFE FH 2" 150# RF 316L SS Seal-Tyte G0 1/2" NPT IA 3" 150# RF Carbon Steel IB 3" 150# RF 316/316L Stainless Steel J2 3" Tri-Clamp JB 3" 300# RF...

Open the catalog to page 8

All AMETEK Drexelbrook catalogs and technical brochures

  1. Model 375

    4 Pages

  2. Model 575P

    4 Pages

  3. Model 675

    5 Pages

  4. Model 575S

    5 Pages

  5. Model SDT

    4 Pages

  6. DR6300 Series

    17 Pages

  7. DR5200 Series

    17 Pages

  8. Z4-Series

    6 Pages

  9. Model DDMC

    8 Pages

  10. Point Level

    5 Pages

Archived catalogs

  1. Model SDT

    4 Pages

  2. DR7000

    4 Pages