Group: Ametek LMS
Catalog excerpts
DATA SHEET Point Level Switch Intelligent Electronics • No calibration or setpoint adjustments. • Ignores changes in dielectric or conductivity. • Automatically recognizes and ignores coatings to prevent false alarms. • Continuous self-test monitors circuits and sensing elements for faults. • Universal power supply automatically detects input power source. Diverse Applications • Detects the absence or presence of liquids, slurries, interfaces and granulars. Output • (2) SPDT relays; relay#2 can be configured as an alarm or fault. Dual Compartment Housing • Power Supply is isolated from intrinsically-safe sensing element and circuit board. Remote or Integral Electronics • Unlike many technologies, electronics can be remote mounted to a convenient or safe location One of the Drexelbrook RF Point Level Switches You Won't Have to Calibrate Simply install the IntelliPoint RF Series into the tank and apply power...that's it! Unlike other RF or capacitance systems that require calibration via setpoint potentiometers, jumpers, magnets, or pushbuttons, the IntelliPoint RF Series reliably detects the absence or presence of material without any adjustments. The IntelliPoint RF Series software continuously monitors the application for changes in composition, dielectric or conductivity, and maintains a repeatable trip point on the probe. Other RF and capacitance systems require calibration adjustments when the process material is changed. Since the the IntelliPoint RF Series recognizes changes in material, it is ideal for non-dedicated tanks that are used for a wide variety of products. Universal Power Supply The IntelliPoint electronics use a universal power supply module that can be powered from a 85 to 250 Vac or 21 to 100 Vdc supply without moving jumpers. Self-Test Feature Automatic and manual test functions ensure proper system operation. An AutoVerify™ selfcheck circuit continuously monitors that the complete system is functioning properly. The Manual Certify not only checks the function of the system, but also checks the AutoVerify self-test circuits to make sure that they are also working properly. Dual Compartment Housing New dual compartment housing separates the customer wiring and power supply from the sensing element and operating circuits. The encapsulated power supply/terminal block design eliminates the possibility of damage caused by moisture in the conduit.
Open the catalog to page 1Calibration: None. Modes Of Operation: High and Low Level. Repeatability: 2 mm (0.08 inch) conductive liquids. Response Time: Less than one second. Ambient Electronic Temperature: -30 to 70°C (-28 to 158°F) ATEX. -40 to 70°C (-40 to 158°F) FM / FMc. Maximum Switching Capacity: 2000 VA/150 Watt. Minimum Contact Load (DC): 100 mA/12 Vdc. 0 to 200 mA / 12 VDC (Optional) Housing: Dual Compartment, Powder-Coated aluminum with two cable entries. Cable Entry: M20 x 1.5 CENELEC %-inch NPT FM / FMc. Ingress Protection: IP66 NEMA 4X. Storage Temperature: -40 to 85°C (-40 to 185°F). Indicators: LEDs:...
Open the catalog to page 2IntelliPoint RF™ Series Z-tron IV™ Z02X-Series Model Numbering (continued on next page) IntelliPoint RF TM RF Admittance Measurement Type L No Calib., 2 pF Fixed Preload P No Calib., 0.5 pF Fixed Preload (High Sensitivity) Manual Calibration Manual Calibration (High Sensitivity) No Calib., 10 pF Fixed Preload No Approvals, NEMA 4X/IP66, M20 X 1.5 conduit entries No Approvals, NEMA 4X/IP66, ¾” NPT conduit entries ATEX Approved, NEMA 4X/IP66, M20 X 1.5 conduit entries FM / FMc Approved, NEMA 4X/IP66, ¾” NPT conduit entries No Approvals, NEMA 4X/IP66, M20 X 1.5 conduit entries, Dual Seal,...
Open the catalog to page 3Model Numbering (continued from p revious page) Plugged Chute Detection (1) (5) Application Sensing Element Pressure/Temperature 305mm2 (12 inches2) extra heavy duty 55 Flush Mount Sensor 700-0207-006 remote 0.1 bar @ 82°C (1 PSI @ 180°F) heavy duty High Pressure / High Temperature 60 High Pressure & Temp. 700-0204-038 remote 137.9 bar @ 93°C (2000 PSI @ 200°F) 316SS and Ceramic ZZ Sensing Element Not Listed Mounting Type (See separate Mounting Chart for first three digits) IL/CSL factory set for Fly Ash Other Notes: CSL (Cote-Shield Length) should extend through...
Open the catalog to page 4All AMETEK Drexelbrook catalogs and technical brochures
-
Multipoint II Series
2 Pages
-
ClearLine Series
2 Pages
-
1500 SERIES RELAY
2 Pages
-
7014 and 7010 Series
2 Pages
-
Unifloat Level Sensors
9 Pages
-
Universal IV ™ CM Model
8 Pages
-
Model 375
4 Pages
-
Model 575 Series
5 Pages
-
Model 575P
4 Pages
-
Model 675
5 Pages
-
Dumpstar Series
2 Pages
-
Plugged Chute Detector
4 Pages
-
Universal II Series
2 Pages
-
Level Mate III
4 Pages
-
Model 575S
5 Pages
-
Model SST Slim-Line
4 Pages
-
Model SDT
4 Pages
-
Total Tank Level System
6 Pages
-
Drexelbrook Level Measurement
16 Pages
-
DR6300 Series
17 Pages
-
DR5200 Series
17 Pages
-
DR7000 Series
4 Pages
-
Z4-Series
6 Pages
-
Universal IV Sales Brochure
10 Pages
-
Coal and Fly Ash Solutions
6 Pages
-
RXL Series, IntelliPoint
4 Pages
-
401-400 Series
4 Pages
-
Model DDMC
8 Pages
-
Accessories Drexelcage
2 Pages
-
Point Level
5 Pages
Archived catalogs
-
USonic™ Series
4 Pages
-
PNT Series, ThePoint
4 Pages
-
Model SDT
4 Pages
-
701X Series Data Sheet
2 Pages
-
CM3 Series Cut Monitor
4 Pages
-
DR7000
4 Pages