A Leader In Level Measurement Solutions Two-Wire RF Series Point Level Switch One of the Drexelbrook RF Point Level Switches You Won't Have to Calibrate Simply install ThePoint Series into the tank and apply power…that's it! Unlike other RF or capacitance systems that require calibration via setpoint potentiometers, jumpers, magnets, or pushbuttons, ThePoint Series reliably detects the absence or presence of material without any adjustments. Intelligent Electronics Save Time and Money • UNIQUE! - NO calibration or setpoint adjustments. • UNIQUE! - Ignores changes in dielectric or conductivity. • Automatically recognizes and ignores coatings to prevent false alarms. Diverse Applications • Detects the absence or presence of liquids, slurries, and granulars. • Capable of high pressures and temperatures. Economical Without Sacrifice • Retains superior performance. • Less maintenance than other technologies; no moving parts to hang up or wear out. Output • 8mA (Alarm), 16mA (Normal) or • 8mA (Normal), 16mA (Alarm) ThePoint Series software continuously monitors the application for changes in composition, dielectric or conductivity, and maintains a repeatable trip point on the probe. Other RF and capacitance systems require calibration adjustments when the process material is changed. Since ThePoint Series recognizes changes in material, it is ideal for non-dedicated tanks that are used for a wide variety of products. Lower Cost of Ownership In addition to lower initial investment, ThePoint continues to save with little or no maintenance compared with other technologies. Further, the sensor can be lengthened or shortened in the field, saving need for additional purchases. Remote or Integral Electronics Unlike many technologies, electronics can be remote mounted to a convenient or safe location

The Point™ Specifications Approvals: Calibration: None Explosion Proof for Class I, Division 1, Groups B, C, and D; Dust Ignition Proof for Class II, III, Division 1, Groups E, F, and G; Non Incendiary for Class I, Division 2, Groups A, B, C, and D; Suitable for Class II, III, Division 2, Groups F and G hazardous classified) locations Outdoor Type 4, 4X, IP66 with Intrinsically Safe connections to Class I, II, III, Division 1, Groups A, B, C, D, E, F, and G hazardous (classified) locations in accordance with control drawing 420-0004-220-CD Modes Of Operation: High and Low Level Repeatability:...

The Point™ Model Numbering (continued on next page) Technology P RF Admittance Measurement Type N Std Auto Cal L Std 2 pF Fixed T 10 pF Auto Cal V 10 pF Fixed Hi Sense .5 pF Auto Cal Hi Sense .5 pF Fixed Hi Sense Manual Std Sense Manual NOTE: All Calibration modes are built into the standard unit. Modes can be changed in the field as required. (See Instruction Manual) Input T Two Wire Power Supply 13 to 30 Vdc Output 0 8-16 mA Housing 0 1 2 3 5 6 7 9 A B (Continued on Next Page) No Approvals, NEMA 4X/IP66, M20 X 1.5 conduit entries No Approvals, NEMA 4X/IP66, ¾” NPT conduit entries ATEX / Testsafe...

Model Numbering Heavy duty, agitated 700-0202-043 remote tanks or material with high bulk density (1) 16 High Integrity Seal for 700-0002-360 int/rem Hazardous Materials 17 Sanitary (3) lowpressure 700-0202-036 int/rem 18 Corrosive material, (continued from previous page) 700-0001-022 int/rem higher pressure with waterlike viscosity (4) 19 Interface Measurement 700-0002-023 int/rem 69 bar @ 38°C (1000 PSI @ 100°F) 34.5 bar @ 149°C (500 PSI @ 300°F) 20 Miniature Pilot 700-0209-002 remote 6.9 bar @ 121°C (100 PSI @ 250°F) Plant Sensor (1)(7) 0 bar @ 232°C (0 PSI @ 450°F) Fly Ash Precipitators,...