Catalogs >
AMETEK Drexelbrook >
Model 575S

Model 575S
5Pages

Catalog excerpts

DATA SHEET Model 575P protected flush diaphragm with optional 3/4" plate Description The Model 575 is used in general water/wastewater applications. The transmitter is offered in a standard non-clogging snub nose end, flush diaphragm or protected flush diaphragm with flange base for sewage or sludge type media. The 575 series is CSA approved for intrinsically safe operation when used with an approved safety barrier. The sensor is designed to provide the convenience of direct submergence in many types of liquids for quick, accurate and reliable measurement. With stainless steel isolation diaphragm (standard) and all 316 stainless steel housing, these solid state instruments provide long lasting service with virtually no maintenance. The 575 Series transmitters indicate the level of liquid by continuously measuring hydrostatic pressure via its sensing element, an ion implanted silicon semiconductor chip with integral Wheatstone bridge circuit. The pressure measurement is transmitted by a 4-20 mA output signal. This design, with isolation diaphragm for media compatibility, provides for excellent linearity and repeatability, low hysteresis and long term stability with a precision accuracy at ±0.25% FS (BFSL) typical. The transmitter is easy to install. Simply lower the unit into a tank or vessel. All electronics are mounted in the submersible 316 stainless steel housing and full potting is also provided as an option. A special cable support bracket is also available to provide extra stability when used with longer cable lengths or when used in an agitated liquid. Optional steel support cable is also available for use with the support bracket. The transmitters are available calibrated for any span needed from 0-6 psi (0-13.8 ft of water, 0-.4 bar, 0-4.2 meters of water) to 300 psi (0-692 ft of water, 0-20 bar, 0-211 meters of water). The transducer is offered as a standard 2 wire, 4-20 mA device. To complete your liquid measurement and control system, consider the Model DDMC meter/controller or the complete Levelmate III system. The 575 transducer is manufactured in the United States under ISO 9001:2008 and meets ARRA. Features • Low cost measurement solution, easy installation and precision accuracy • Rugged 316 stainless steel construction and wetted materials resists the corrosive effects of caustic medias with excellent environmental protection, designed for continuous submersion • 2 wire, 4 to 20 mA output • Reverse polarity and surge protected with additional lightning and surge protectors as well as EMI protection options • CSA approved for intrinsically safe operation in hazardous areas in Canada and U.S. • Full potting option and desiccant available to minimize moisture effects Applications • Inventory tank measurement • Water wells • Ponds, rivers and lakes • Landfills • Lift stations and slurries or sludge • Pump control • Water/wastewater treatment

Open the catalog to page 1

Specifications Feet of Water: 0/14, 0/35, 0/69, 0/138, 0/230, 0/345, 0/460, 0/690 Meters of Water: 0/4, 0/10, 0/21,0/42, 0/70, 0/105, 0/140, 0/210 Bar: 0/0.4, 0/1,0/2, 0/4, 0/7, 0/10, 0/14, 0/20 PSI: 0/6, 0/15, 0/30, 0/60, 0/100, 0/150, 0/200, 0/300 Output: 4 to 20 mA, 2 wire, current limited to 30 mA DC Power Supply: 12 to 40 VDC with reverse polarity surge protection; Limited to 28 VDC for CSA I.S. Loop Resistance: 1400 ohms maximum at 40 volts Temperature Range**: General Ambient Operating: -25° to 180°F (-32° to 82°C) ** CSA intrinsically safe when connected per AMETEK drawing BK750535....

Open the catalog to page 2

Product Data Model 575 Series ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Submersible Level Transmitter Model 575 Series Submersible Level Transmitters 575PB Protected Flush Diaphragm 1/16" Thick Plate 575PB Protected Flush Diaphragm With 3/4" Plate (J Option) For Tank, Pipe or Vessel Mount Optional Conduit Adapter In Line Desiccant Option For Use With Vent Tube Cables Part #K234436 (original assembly desiccant with hardware) Transmitter With Desiccant Part #K234446 (replacement cartridge ONLY – requires some assembly of parts from original assembly) Optional Cable Support Bracket With Nut and...

Open the catalog to page 3

Product Data Model 575 Series ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Submersible Level Transmitter Model 575 Series Model Numbering Submersible Level Transmitters Model Numbering: 575 level transmitter 575 Series submersible level transmitter Nylon snub nose (standard) Stainless steel snub nose Flushmount Protected flush Reference equivalents 0-13.8 ft. water 0-34.6 ft. water 0-69.2 ft. water 0-138 ft. water 0-230 ft. water 0-345 ft. water 0-460 ft. water 0-690 ft. water 0-4.2 meters water 0-10.5 meters water 0-21.1 meters water 0-42.2 meters water 0-70.3 meters water 0-105.4 meters water...

Open the catalog to page 4

Model 575 Series Submersible Level Transmitter Display Meters, Surge Protectors, Junction Boxes and Desiccants DISPLAY METERS AND SYSTEMS Model DDMC Digital Meter/Controller Dual display meter provides power to the sensor with alarm and 4-20 mA analog output options. Standard panel mount housing or a NEMA 4X weathertight housing for field mounting is available. The weathertight housing also provides internal mounting locations for lightning and surge protectors. LEVEL MATE™ III Level Measurement System The complete LEVEL MATE III system includes a level sensor (various models are...

Open the catalog to page 5