Group: Ametek LMS
Catalog excerpts
DATA SHEET Protected Flush Submersible Level Transmitter Description The Model 575P Protected Flush Submersible Level Transmitter has a HASTELLOY C diaphragm in a special, protective flange, for sewage applications. The unit is specially designed to provide the convenience of direct submergence in many types of liquid, especially wastewater, for quick, accurate and reliable level measurement. The simple design and rugged construction of these solid state instruments provide long lasting service with virtually no maintenance. The 575P Transmitter indicates the level of liquid by continuously measuring hydrostatic pressure via its sensing element, an ion implanted silicon semiconductor chip with integral Wheatstone Bridge circuit. Once the sensor measures the pressure, the data is transmitted by a 4 to 20 mA output signal. This design provides for excellent linearity and repeatability, low hysteresis and long term stability. The transmitter is easy to install. Simply lower the transmitter into a tank. All the electronics are mounted in a submersible 316 stainless steel housing. A special cable support bracket is also available. This gives extra stability to the transmitter when used with longer lengths of cable or when used in an agitated liquid.* The transmitters are available calibrated for any span needed, from 0 to 3 psi or 0 to 0.2 bar (0 to 7 feet or 0 to 2.1 meters of water) to 0 to 300 psi or 0 to 20 bar (0 to 690 feet or 0 to 211 meters of water). To complete your liquid level measurement and control system, use the AMETEK Model DDMC Digital Meter/ Controller with the 575 Series Transmitters. Features • CSA approved for intrinsically safe operation • Solid state semiconductor sensor for accuracy and reliability • Rugged 316 stainless steel housing with excellent environmental protection • Easy to install and use • 2 wire 4 to 20 mA output • Vented to the atmosphere through the surface end of the cable • Reverse polarity and surge protected • Lightning protectors available • EMI protection available • Optional heavy base model • HASTELLOY C standard flush diaphragm Applications • Water/wastewater treatment • Tanks • Slurry/sludge • Ponds • Lift stations • Water wells • Pump control • Level control AMETEK’ DREXELBROOK www.Drexel
Open the catalog to page 1Model 575P Protected Flush Submersible Level Transmitter Product Data Specifications Electrical Connection: Attached 20 gauge polyurethane shielded cable – unspliced lengths available up to 5000 feet (1662m) Power Supply: 0/10, 40 VDC with reverse 0/140, Meters of Water: 0/4, 12 to 0/21, 0/42, 0/70, 0/105, polarity surge 0/210 protection; Limited to 28 VDC for CSA I.S. Loop Resistance: 0/7, 0/10, 0/14, 0/20 Bar: 0/0.4, 0/1, 0/2, 0/4,1400 ohms maximum at 40 volts Approvals: Meets CSA requirements for intrinsically safe operation in requirements for intrinsically safe operaApprovals: Meets...
Open the catalog to page 2Model 575P Protected Flush Product Data Submersible Level Transmitter ELECTRONIC LEVEL MEASUREMENT PRODUCTS Model 575P Protected Optional Heavy Base The Model with heavy 4" Flush575P is available thick afor use whereLevel Transmitter Submersible diameter bottom plate, 3/4" turbulence or higher Optional Heavy Base flow rate might require more weight and stability. Unit can be ordered with The Model 575P is available with a heavy 4" diameter this optional base or user may purchase a field bottom plate, 3/4" thick for use where turbulence or conversion kit (P/N K680029). Field conversion...
Open the catalog to page 3Product Data Model 575P Protected Flush ELECTRONIC LEVEL MEASUREMENT PRODUCTS Submersible Level Transmitter Model 575P Protected Model Numbering Flush Submersible Level Transmitter Model Numbering: 575 level transmitter 575 Series submersible level transmitter Sensing port P Protected flush Input/Output* B 0 to 6 psi/0 to 0.4 bar (0 to 14 ft./0 to 4.2 m water) 0 to 15 psi/0 to 1 bar (0 to 35 ft./0 to 10.5 m water) 0 to 30 psi/0 to 2 bar (0 to 69 ft./0 to 21.1 m water) 0 to 60 psi/0 to 4 bar (0 to 138 ft./0 to 42.2 m water) 0 to 100 psi/0 to 7 bar (0 to 230 ft./0 to 70.3 m water) 0 to 150...
Open the catalog to page 4All AMETEK Drexelbrook catalogs and technical brochures
-
Multipoint II Series
2 Pages
-
ClearLine Series
2 Pages
-
1500 SERIES RELAY
2 Pages
-
7014 and 7010 Series
2 Pages
-
Unifloat Level Sensors
9 Pages
-
Universal IV ™ CM Model
8 Pages
-
Model 375
4 Pages
-
Model 575 Series
5 Pages
-
Model 675
5 Pages
-
Dumpstar Series
2 Pages
-
Plugged Chute Detector
4 Pages
-
Universal II Series
2 Pages
-
Level Mate III
4 Pages
-
Model 575S
5 Pages
-
Model SST Slim-Line
4 Pages
-
Model SDT
4 Pages
-
Total Tank Level System
6 Pages
-
Drexelbrook Level Measurement
16 Pages
-
DR6300 Series
17 Pages
-
DR5200 Series
17 Pages
-
DR7000 Series
4 Pages
-
Z4-Series
6 Pages
-
Universal IV Sales Brochure
10 Pages
-
Coal and Fly Ash Solutions
6 Pages
-
RXL Series, IntelliPoint
4 Pages
-
401-400 Series
4 Pages
-
Model DDMC
8 Pages
-
Accessories Drexelcage
2 Pages
-
Point Level
5 Pages
Archived catalogs
-
USonic™ Series
4 Pages
-
PNT Series, ThePoint
4 Pages
-
Model SDT
4 Pages
-
701X Series Data Sheet
2 Pages
-
CM3 Series Cut Monitor
4 Pages
-
DR7000
4 Pages