Group: Ametek LMS
Catalog excerpts
DATA SHEET Economical level switch The B/W 7014 and 7010 float switch products offer an economical solution to clean liquid point level measurement. Multiple switch points The B/W float switches offer single point or up to 12 switch points on a single guide tube. Direct or Indirect operation Switches can close on rising level or open on rising level Suitable for many Applications Applicable to clean liquids for high or low level indication, pump control, and stop fill on storage vessels. Reliable mechanical point level switches for use in many clean liquids applications. Float switches provide general-purpose point level device at an economical price. Simple installation and reliable operation make floats a good choice for many point level applications. B/W float switches provide reed switch or mechanical switch outputs that can connected to B/W relay Modules for control function or directly to a PLC or DCS system. Relays are available for general purpose and with intrinsically safe outputs for hazardous areas. B/W Floats are available in a variety of materials for use in many different process liquids. 7014 Unifloat™ Specifications Output: Type C or Type I Reed switch (Type I for direct connection to PLC or DCS) Material of Construction: 316SS (Brass optional) Number of switch points: Up to 12 Maximum Length of guide tube: Up to 12 feet Operating Temperature: 0 to 250 degrees F Operating Pressure: Vacuum to 14,7 psi 7010 Tilt Switch Specifications Output: Mercury switch or mechanical S.P.D.T. Material of Construction: Polypropylene Number of switch points: One Maximum Length of tether cord: 20 feet standard (longer length available) Operating Temperature: 32 to 160 degrees F Operating Pressure: Vacuum to 26 psi
Open the catalog to page 1Model Numbering Tilt Switch 7010 X Tether Length UniFloat™7014 X- Note - Additional length wire is spliced to existing float wire. Special epoxy heat shrink tube is used to assure watertight seal. Note - Complete "Reed Switch Specification Chart" in Application Worksheet section to indicate reed switch function and location. Guide Tube Material Brass 316 Stainless Steel AMETEK DREXELBROOK www.Drexelbrook.com Phone: +1 215-674-1234 • Fax: +1 215-674-2731 E-mail: drexelbrook.info@ametek.com 205 Keith Valley Road | Horsham PA 19044 U.S.A.
Open the catalog to page 2All AMETEK Drexelbrook catalogs and technical brochures
-
Multipoint II Series
2 Pages
-
ClearLine Series
2 Pages
-
1500 SERIES RELAY
2 Pages
-
Unifloat Level Sensors
9 Pages
-
Universal IV ™ CM Model
8 Pages
-
Model 375
4 Pages
-
Model 575 Series
5 Pages
-
Model 575P
4 Pages
-
Model 675
5 Pages
-
Dumpstar Series
2 Pages
-
Plugged Chute Detector
4 Pages
-
Universal II Series
2 Pages
-
Level Mate III
4 Pages
-
Model 575S
5 Pages
-
Model SST Slim-Line
4 Pages
-
Model SDT
4 Pages
-
Total Tank Level System
6 Pages
-
Drexelbrook Level Measurement
16 Pages
-
DR6300 Series
17 Pages
-
DR5200 Series
17 Pages
-
DR7000 Series
4 Pages
-
Z4-Series
6 Pages
-
Universal IV Sales Brochure
10 Pages
-
Coal and Fly Ash Solutions
6 Pages
-
RXL Series, IntelliPoint
4 Pages
-
401-400 Series
4 Pages
-
Model DDMC
8 Pages
-
Accessories Drexelcage
2 Pages
-
Point Level
5 Pages
Archived catalogs
-
USonic™ Series
4 Pages
-
PNT Series, ThePoint
4 Pages
-
Model SDT
4 Pages
-
701X Series Data Sheet
2 Pages
-
CM3 Series Cut Monitor
4 Pages
-
DR7000
4 Pages