Catalogs >
Ametek Calibration >
CrystalCalHP

CrystalCalHP
7Pages

Catalog excerpts

A Better Way to CalibrateAutomate Your Calibrations: 7 to 10 Times Faster than a Deadweight Tester The GaugeCalHP Comparator ► Generates pressure up to 15 000 psi. ► Works with oil, water, or air.* ► Faster than any deadweight tester and most automated pressure controllers. ► Use in a lab or out in the field. (*up to 400 inH20) AMETEK* SENSORS, TEST & CALIBRATION FastCalXP Software ► Calibrate gauges, transmitters, transducers, and chart recorders. ► 10 point up and down calibration in less than 3 minutes. ► Eliminates typing. ► Reduces calculation errors. ► Saves time on each...

Open the catalog to page 2

precision hydraulic pressure comparator Connection Fitting With easy alignment swivel capability. Relief Valve No Mess Drip Tray Captures fluid from bleeding the system. intended for the calibration of pressure gauges, transmitters, sensors, and safety valves rated up to 15 000 psi / 1000 bar. Fine Adjust Easy to use, even at 15000 psi. Pivot Manifold Manifold rotates for testing large size gauges. You may fill the comparator with your Reservoir Clear, removable reservoir with a fill line. choice of water or oil, or use without fluid up to 400 inH2O. The GaugeCalHP is much faster than...

Open the catalog to page 3

Systems ^^rystalCalHP calibration systems are available in two configurations: basic and expanded systems. The expanded systems include three ultra-rugged, intrinsically safe XP2i digital test gauges. With its 0.1% of reading accuracy, XP2i has long been the industry standard, and the world's most popular test gauge Basic Systems CrystalCalHP-NPT/ CrystalCalHP-BSP Common Components Expanded Systems CrystalCalHP-NPT-PSI/CrystalCalHP-BSP-PSI Basic System with psi Gauges Part Number CrystalCalHP-NPT-BAR/CrystalCalHP-BSP-BAR Basic System with bar Gauges Included with -NPT System Part Number...

Open the catalog to page 4

Specifications GaugeCalHP Maximum Hydraulic Pressure . . . . . . 15 000 psi/1000 bar/100 MPa Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . . -12.5 psi/-0.86 bar/-86.2 kPa . . Maximum Pneumatic Pressure. . . . 400 inH2O/995 mbar/29 inHg Sensitivity (fine adjust). . . . . . . . . . . . . . . . . . . 0.01 inH2O/0.025 mbar Burst Pressure. . . . . . . . . . . . . . . . . . . . >25 000 psi /1700 bar /170 MPa Materials Wetted Materials. . . . . . . . . . . . . . . . . . . . . . . Stainless Steel plus Seals and Acrylic Reservoir Enclosure. . . . . . . . . . . . . . . . . . . . . . . ....

Open the catalog to page 5

Display Resolution ■ Unneeded pressure units may be disabled via the RS-232 connector using ConfigXP software. ■ kPa models can display pressure in kPa, MPa, and bar (or mbar) only. psi and bar models can display all available units.

Open the catalog to page 6

No part of this document may be reproduced or modified in any form or by any means, electronic or mechanical, without express written permission from Crystal Engineering Corporation. ©2015 Crystal Engineering Corporation AMETEK* SENSORS, TEST & CALIBRATION

Open the catalog to page 7

CrystalCalHP 7Pages

Catalog excerpts

All Ametek Calibration catalogs and technical brochures

CrystalCalHP
7Pages