TURRET PUNCH PRESS TOOLING
72Pages

TURRET PUNCH PRESS TOOLING STANDARD SHAPES & FORMING SPECIAL PURPOSE TOOLS

PUNCH PRESS

umit pLuutiij lutiiwa A(V), B(l1/4") NEX spring & PV die performance guide 1 - 2 A(V') Tip type round / original (0 0.8 ~ 0 1.5mm) 2 B (IV) Shape Air-Blow : inscribed 0 30.0mm / Original : 0 12.71 ~ 0 31.7mm 11-12 C (2"), D (3V) Large station guide list 15 St C (2"), D (3V), E (4V) Sheet saver guide, stripper & die 16 E (4V) Large Station Guide List 16 D (3V) Round & shape solid type & tip type 19 - 20 E(4V) Round & shape solid type & tip type 21-22 B (IV) FP (Flat Positioning) tool 28 A (V) Upform center punch tool 29 A (V) Downform center punch & High speed marking tool 29 C(2")...

Assembly / Desassembly device A (V) to E (4V) 41 Slug ejector replacement kit 42 Automatic tool grinding machine TOGU EU 43 - 44 Special shape tooling (Semi-standard tooling) Punching tool steel type & features Cautions and instructions about tooling Shape, size and key angle Table of recommended die clearance Punching force calculation method Minimum punchable hole diameter C (2") Alpha guide assy D (3V) Alpha guide assy E (4V) Alpha guide assy C (2") Alpha sheet saver guide assy D (3V) Alpha blade guide assy E (4V) Alpha blade guide assy C (2") Thick Turret Z style guide parts list D (3V)...

Punch body replacement and height adjustement become so easy by new spring assy mechanisms. Tooling costs is dramatically reduced by spring assy + guide combination and by the the grind length increase. --- Tooling recommanded for EM series of machines --- NEX Spring Assy For long tooling A (1/2’’) and B (11/4’’) Maxthickness 6.0mm Mild steel - aluminum max 6.0mm Stainless steel max 3.0mm Nex spring assembly can be use for both Air-Blow and original style punch body Grinding amount increased to a maximum of 5.0 mm Maintenance time reduce to 1/3 maximum of 5.0 mm. This means that a punch...

Power Vacuum Die: standard die for EM & AC for A (1/2’’) et B (11/4’’) Vacuum suction unit by air jet flowing downwards in the die preventing slug-pulling Ejector pipe Tooling size Vacuum unit Turret size Same diameter turret Die has a small pin holes aiming toward downward , and this creates maximum vacuum effect. Slug vacuum system by strong jet air projected toward downward under the die. * Power vacuum die cannot be applied on PKK die and back tapered die, because of less effectiveness of slug-pulling prevention. * Z turret uses AJV system, air projected position is different from power...

Punch assy 208 (Punch height 207.5 / Punch body 207) Punch body Open guide 208 (Punch height 207.5 / Punch body 207) Punch assy Punch body Open guide Closed guide Closed guide * Closed guide is recommended for EM machine. Punch assy 209.5 (Punch height 207.5 / Punch body 207) Original style O-ring type for retainer Closed guide Install O-ring on to guide Punch body Open guide Closed guide Open guide

■ Tooling selection and code * Retainer slug profile

Punch body Open guide Punch assy Punch assy 208 (Punch height 207.5 / Punch body 207) Closed guide 208 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide * Closed guide is recommended for EM machine. * Punch bigger than 䃱6.0mm diameter has a center hole. * Punch bigger than شñ6.0mm diameter has a slug ejector. Original style Punch assy 209.5 (Punch height 207.5 / Punch body 207) O-ring type for retainer Closed guide Install O-ring on to guide Punch body Open guide Closed guide * Punch bigger than شñ6.0mm diameter has a slug ejector. Open guide

(VjSize ROUND ■ Tooling selection and code * Retainer slug profile

Punch body Open guide Punch assy 208 (Punch height 207.5 / Punch body 207) Closed guide Punch assy 208 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide * Closed guide is recommended for EM machine. * Punch bigger than 䃱6.0mm diameter has a center hole. * Punch bigger than شñ6.0mm diameter has a slug ejector. Original style O-ring type for retainer Punch assy 209.5 (Punch height 207.5 / Punch body 207) Closed guide Install O-ring on to guide Punch body Open guide Closed guide * Punch bigger than شñ6.0mm diameter has a slug ejector. Open guide

■ Tooling selection and code * Retainer slug profile Additional cost * Aditional keyway (Standard keyway : 0° ,90°) * Rooftop 2°forA/B/C/D Station (E Station Standard) * Narrow type (Stubby punch): Shape under 2.4 mm for A & B St, under 4 mm for C, D & E St.

Open guide Punch assy Punch body 208 (Punch height 207.5 / Punch body 207) Punch assy 208 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide Closed guide * Closed guide is recommended for EM machine. * Punch bigger than 䃱6.0mm diameter has a center hole. Punch assy 209.5 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide * Punch bigger than شñ6.0mm diameter has a slug ejector. * Punch bigger than شñ6.0mm diameter has a slug ejector. Original style

■ Tooling selection and code * Retainer slug profile

Air-Blow : inscribed Ø 30.0mm (rectangle less than 10x30mm) Original style : Ø 12.71 ~ Ø 31.7mm Punch body Open guide Punch assy 208 (Punch height 207.5 / Punch body 207) Closed guide Punch assy 208 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide * Le guide fermé est recommandé pour la machine EM. * Un poinçon supérieur à Ø 6 mm a un perçage central. Punch assy 209.5 (Punch height 207.5 / Punch body 207) Punch body Open guide Closed guide * Punch bigger than 䃱6.0mm diameter has a slug ejector. * Punch bigger than شñ6.0mm diameter has a slug ejector. Original style

B(iV)Size SHAPE ■ Tooling selection and code * Retainer slug profile Additional cost * Aditional keyway (Standard keyway : 0° ,90°) * Roof top 2° for A/B/C/D Station (E Station Standard) * Narrow type (Stubby punch): Shape under 2.4 mm for A & B St, under 4 mm for C, D & E St.