Overview of fans & accesories - ERP 2015
11Pages

ErP 2015 The ErP Directive New values for fans

What is ErP 2015? ErP, that is, ”Energy related Products” means products related to energy. In order to accomplish the objectives of the EU Climate and Energy Package the EuP directive - “Energy-Using Products” was issued in 2005, which was thereafter replaced by the ErP directive in 2009. This directive specifies the rules for setting requirements concerning the energy related products, including electric motors used in fans. The main purpose of the ErP directive is to increase the efficiency of the rotor-fan units by 20%. It also supports the accomplishment of the objectives set in the EU...

the air stream, exceeds 65 °C; • when the temperature of the moved air or the ambient temperature during the operation of the motor being outside the air stream are lower than – 40°C; • if the supply voltage exceeds 1000 V in the case of AC power supply or 1500 V in the case of DC power supply; • in the conditions of exposure to toxic, flammable or strongly corrosive agents or in the conditions of exposure to abrasive substances; e) provided with the heat exchanger or thermal pump, serving the purpose of heat recovery or enabling the transfer or heat recovery additionally for the operation...

Duct fans Model: DV-PP-L The DV-PP-L duct fan is used to supply and exhaust the air in ventilation ducts. The DV-PP-L duct fans are an ideal solution for the air exhaust in bathrooms and other rooms. Small sizes of the DV-PP-L fans facilitate the assembly in locations that are hard to access and where the space is limited. Model: DV-PP Intended for general ventilation with the low degree of dusting the round duct fan is characterised by high efficiency at minimum noise level. It can be mounted both in the vertical and horizontal arrangement, and the universal construction enables its...

Roof fans DV-ROF-R 355 ENERGIA · ЕНЕРГИЯ · ΕΝΕΡΓΕΙΑ · ENERGIJA · ENERGY · ENERGIE · ENERGI Model: DV-ROF-R A+++ A++ A+ The DV-ROF-R roof fan with horizontal air discharge is available in two versions of the winding insulation class - B and F. The DV-ROF roof fan has a broad range of applications: industrial and construction applications, in factories, hospitals, night clubs, theatres, houses, restaurants. The exhaust fans are intended for installation on dampening roof bases. Model: DV-ROF-V DV-ROF-V roof fan with vertical air discharge It is available in two versions of the winding...

Technical data of duct fans Dimensions [mm] Casing material Rotor material galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel galvanised steel ALNOR® systemy wentylacji jest prawnie chronionym znakiem i technicznym patentem. Prawo do zm

recommended ERV speed regulator protection class Insulation class energy class Technical data of duct fans ALNOR® systemy wentylacji jest prawnie chronionym znakiem i technicznym patentem. Prawo do zmian zastrzeżone.

Technical data of roof fans Fan . . of transported level . ,,, , pressure Casing material Rotor material painted steel painted steel painted steel painted steel painted steel painted steel painted steel ALIMOR systemy wentylacji jest prawnie chronionym znakiem i technicznym patentem. Prawo do zmian zastrzezone

recommended ERV speed regulator protection class Insulation class energy class Technical data of roof fans ALNOR® systemy wentylacji jest prawnie chronionym znakiem i technicznym patentem. Prawo do zmian zastrzeżone.

Complete system for roof fan assembly PDI-BRF roof lead-in The roof lead-in fits the BRF/DV-ROF-R fans, which occur in two versions of the winding insulation class B and F. In the case of mounting the fan directly on the lead-in, use the USZ gasket at the location where the fan gets into contact with the lead-in. The roof lead-in can be provided at an angle of 1-60 degrees. Lead-in height - 100 or 500 mm. The lead-in is insulated with wool with the thickness of 30 mm and 50 mm, depending on the size. PDI-BRV roof lead-in The roof lead-in fits the BRV/DV-ROF-V fans, which occur in two...

Complete system for roof fan assembly SPIRO pipe stub connector for the roof fan It can be mounted only on top of the lead-in (between the lead-in and the fan). While mounting the plate onto the lead-in, use the SIL-DEK-310 roofing sealant at the site where the plate joins the lead-in. From the side where the plate joins the fan, use the USZ gasket to ensure leak-tightness. The lead-in fulfils only the role of the thermal insulation. Straight plate with the ILSL or ILSVL pipe stub connector. DV-REG-L electronic speed regulator The electronic fan speed regulator serves the purpose of smooth...