- IP66 100A/125ASW80P Single Pole Single Throw Normally OpenSeries) (Part of the SW80 The SW80P is sealed to IP66 and has been designed for direct current loads in more ardous environments. Applications include winches and motors as used on electric vehicles such as industrial trucks. Developed for both interrupted and uninterrupted loads, the SW80P is suitable for switching Resistive, Capacitive and Inductive loads. Thermal Current Rating (Ith) Intermittent Current Rating: Rated Fault Current Breaking Capacity (Icn) Resistive Load: (in accordance with UL508*) SW80P Uninterrupted current - no or infrequent load switching requirements (maintains a lower contact resistance). The SW80P features single pole double breaking main contacts with silver alloy tips, which are weld resistant, hard wearing and have excellent conductivity. The SW80P features an enclosed top cover and offers environmental protection to IP66. The SW80P has M8 stud main terminals and 6.3mm spade coil connections. Mounted using supplied brackets, mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards. If the requirement is for downwards orientation we can adjust the contactor to compensate for this. Rated Fault Current Breaking Capacity (Icn) 5ms Time Constant: (in accordance with UL583*) SW80P Interrupted current - opening and closing on load with frequent switching (results in increased contact resistance). Maximum Recommended Contact Voltages (Ue): SW80P Typical Voltage Drop per pole across New Contacts at 100A Mechanical M.T.B.F Coil Voltage Available (Us) (Rectifier board required for A.C.) Coil Power Dissipation: Highly Intermittent Rated Types Intermittently Rated types Prolonged Rated Types Continuously Rated Types Maximum Pull-In Voltage (Coil at 20˚ C) Guideline: Highly Intermittent Rated types (Max 25% Duty Cycle) Intermittently Rated types (Max 70% Duty Cycle) Prolonged Operation (Max 90% Duty Cycle) Continuously Rated Types (100% Duty Cycle) Typical Pull-In Time Magnetic Latching† (Not fail safe) Closed Contact Housing Environmentally Protected IP66 EE Type (Steel Shroud) Contact Performance Key: Interrupted Current Uninterrupted Current * Please check our web site for product UL status Performance data provided should be used as a guide only. Some de-rating or variation from figures may be necessary according to application. Thermal current ratings stated are dependant upon the size of conductor being used For further technical advice email: [email protected] Albright reserve the right to change data without prior notice Connection Diagram Current (Amperes) Note: Where applicable values shown are at 20˚C Rated suitable for Application = Interrupted Mounting Brackets (See Stud Range Catalogue) Advised Connection Sizes for Maximum Continuous Current Guideline Contactor Weight: 390 gms Copper busbar Magnetic Blowouts† Magnetic Blowouts - High Powered† Operating Ambient Temperature Figures are for guideline purposes only Typical Contact Bounce Period Auxiliary Contacts With Diode Suppression Time (Seconds) Without Suppression Typical Drop-Out Time (N/O Contacts to Open): With Diode and Resistor (Subject to resistance value) Drop-Out Voltage Range Large Tips Textured Tips Silver Plating AC Rectifier Board (Fitted) Coil Suppression† Flying Leads Manual Override Operation Vacuum Impregnation Connections become polarity sensitive Albright International Ltd, Evingar Trading Estate, Ardglen Road, Whitchurch, Hampshire, RG28 +44 UK Albright International, 125 Red Lion Road, Surbiton, Surrey KT6 7QS, England,Tel: +44 (0) 20 8390 5357, Fax:7BB,(0) 20 8390 1927 Tel: [email protected] or [email protected] Web 890030, Fax: +44 (0)1256 890043 E-mail: +44 (0)1256 893060, Fax: +44 (0)1256 893562, Dedicated Sales Tel: +44 (0)1256 Site: www.albrightinternational.com E-mail: [email protected] or [email protected] Web Site: www.albrightinternational.com Copyright © 2010 Albright International Ltd Copyright © 2013 Albright International LTD