
Catalog excerpts

Thermal Current Rating (Ith) Intermittent Current Rating: 800A at 80V Rated Fault Current Breaking Capacity (Icn) Resistive Load: (in accordance with UL508*) 190A at 60V D.C. 190A at 96V D.C. Maximum Recommended Contact Voltages (Ue): SW80 Uninterrupted current - no or infrequent load switching requirements (maintains a lower contact resistance). The SW80 features single pole double breaking main contacts with silver alloy tips, which are weld resistant, hard wearing and have excellent conductivity. The SW80 has M8 stud main terminals and 6.3mm spade coil connections. Mounting is via M4 tapped holes or mounting brackets, either supplied fitted, or as separate items. Mounting can be horizontal or vertical, when vertical the M8 contact studs should point upwards. If the requirement is for downwards orientation we can adjust the contactor to compensate for this. Interrupted current - opening and closing on load with frequent switching (results in increased contact resistance). The SW80 has been designed for direct current loads, including motors as used on electric vehicles such as industrial trucks, and telecom and power distribution applications. Developed for both interrupted and uninterrupted loads, the SW80 is suitable for switching Resistive, Capacitive and Inductive loads. • 150A Rated Fault Current Breaking Capacity (Icn) 5ms Time Constant: (in accordance with UL583*) SW80 SW80 Single Pole Single Throw Normally Open (Part of the SW80 Series) Typical Voltage Drop per pole across New Contacts at 100A Mechanical M.T.B.F Coil Voltage Available (Us) (Rectifier board required for A.C.) Coil Power Dissipation: Highly Intermittent Rated Types Intermittently Rated types Prolonged Rated Types Continuously Rated Types Maximum Pull-In Voltage (Coil at 20˚ C) Guideline: Highly Intermittent Rated types (Max 25% Duty Cycle) Intermittently Rated types (Max 70% Duty Cycle) Prolonged Operation (Max 90% Duty Cycle) Continuously Rated Types (100% Duty Cycle) Drop-Out Voltage Range Typical Pull-In Time Typical Drop-Out Time (N/O Contacts to Open): Without Suppression With Diode Suppression With Diode and Resistor (Subject to resistance value) Typical Contact Bounce Period With Auxiliary With Blowouts Time (Seconds) Mounting Brackets (See Stud Series Catalogue) Magnetic Latching† (Not fail safe) Auxiliary Contacts - V3 Figures are for guideline purposes only Magnetic Blowouts† Magnetic Blowouts - High Powered† Uninterrupted Current Rated suitable for Application = Interrupted Interrupted Current Advised Connection Sizes for Maximum Continuous Current Cable Current (Amperes) Copper busbar Auxiliary Contact Switching Capabilities (Resistive Load): SW80A Closed Contact Housing‡ Environmentally Protected IP66 (see SW80P Catalogue sheet) 10 Auxiliary Thermal Current Rating Auxiliary Contacts Guideline Contactor Weight: SW80 Operating Ambient Temperature EE Type (Steel Shroud) Contacts Large Tips Connection Diagram Textured Tips Silver Plating AC Rectifier Board (Fitted) Coil Suppression† Flying Leads Note: Where applicable values shown are at 20˚C Manual Override Operation * Please check our web site for product UL status Performance data provided should be used as a guide only. Some de-rating or variation from figures may be necessary according to application. Thermal current ratings stated are dependant upon the size of conductor being used For further technical advice email: technical@albrightinternational.com Albright reserve the right to change data without prior notice Vacuum Impregnation Key: Optional Connections become polarity sensitive Open Housing Available Albright International Ltd, Evingar Trading Estate, Ardglen Road, Whitchurch, Hampshire, RG28 +44 UK Albright International, 125 Red Lion Road, Surbiton, Surrey KT6 7QS, England,Tel: +44 (0) 20 8390 5357, Fax:7BB,(0) 20 8390 1927 Tel: sales@albrightinternational.com or technical@albrightinternational.com Web 890030, Fax: +44 (0)1256 890043 E-mail: +44 (0)1256 893060, Fax: +44 (0)1256 893562, Dedicated Sales Tel: +44 (0)1256 Site: www.albrightinternational.com E-mail: sales@albrightinternational.com or technical@albrightinternational.com Web Site: www.albrightinternational.com Copyright © 2010 Albright International Ltd Copyright © 2013 Albright International LTD
Open the catalog to page 1All ALBRIGHT INTERNATIONAL catalogs and technical brochures
-
About Albright
2 Pages
-
New Mirror Auxiliary Contact
1 Pages
-
SU190
1 Pages
-
DC92 Monoblock, 2 x SW80
1 Pages
-
DC64P Monoblock, 2 x SW60
1 Pages
-
DC88P-100
1 Pages
-
SW61
1 Pages
-
Stud range
7 Pages