PC60 Single Pole Single Throw Normally Open (Part of the PC60 Series) Thermal Current Rating (Ith) Intermittent Current Rating: 30% Duty Interrupted current - opening and closing on load with frequent switching (results in increased contact resistance). Uninterrupted current - no or infrequent load switching requirements (maintains a lower contact resistance). The PC60 is a miniature series single pole single throw contactor designed for printed circuit board mounting. Devised for both interrupted and uninterrupted loads, the PC60 is suitable for switching Resistive, Capacitive and Inductive loads. Typical applications include Telecommunication, UPS and other power conversion systems. Rated Fault Current Breaking Capacity (Icn) 5ms Time Constant: (in accordance with UL583*) PC60 PC60B The PC60 features single pole double breaking main contacts with silver alloy tips, which are weld resistant, hard wearing and have excellent conductivity. The PC60 can be secured to the printed circuit board by means of an M4 bolt. Note: The PC range now incorporates the mounting board option, previously assigned to the MB range (existing MB part numbers remain valid). Rated Fault Current Breaking Capacity (Icn) Resistive Load: (in accordance with UL508*) PC60 Maximum Recommended Contact Voltages (Ue): PC60 Typical Voltage Drop per pole across New Contacts at 80A Mechanical M.T.B.F Coil Voltage Available (Us) (Rectifier board required for A.C.) Coil Power Dissipation: Highly Intermittent Rated Types Intermittently Rated types Prolonged Rated Types Continuously Rated Types Maximum Pull-In Voltage (Coil at 20˚ C) Guideline: Highly Intermittent Rated types (Max 25% Duty Cycle) Intermittently Rated types (Max 70% Duty Cycle) Prolonged Operation (Max 90% Duty Cycle) Continuously Rated Types (100% Duty Cycle) Drop-Out Voltage Range Typical Pull-In Time Enclosed top cover standard when blowouts not fitted Typical Drop-Out Time (N/O Contacts to Open): Without Suppression With Diode Suppression With Diode and Resistor (Subject to resistance value) Time (Seconds) Guideline Contactor Weight: PC60 With Auxiliary With Blowouts Armature Cap Mounting Base (see overleaf) EE Type (Steel Shroud) Magnetic Latching† (Not fail safe) Closed Contact Housing‡ Interrupted & Uninterrupted Current Contacts Large Tips Textured Tips Current (Amperes) Auxiliary Contact Switching Capabilities (Resistive Load): Magnetic Blowouts - High Powered† Auxiliary Thermal Current Rating Magnetic Blowouts† Figures are for guideline purposes only Auxiliary Details Auxiliary Contacts Operating Ambient Temperature Typical Contact Bounce Period Silver Plating Coil AC Rectifier Board (Fitted) Coil Suppression† Flying Leads Manual Override Operation Note: Where applicable values shown are at 20˚C * Please check our web site for product UL status Advised Connection Sizes for Maximum Continuous Current Circuit Board Tracks Key: Rated suitable for Application = Uninterrupted Performance data provided should be used as a guide only. Some de-rating or variation from figures may be necessary according to application. Thermal current ratings stated are dependant upon the size of conductor being used For further technical advice email: [email protected] Albright reserve the right to change data without prior notice Vacuum Impregnation Key: Optional Connections become polarity sensitive Enclosed top cover standard when blowouts not fitted Not Suitable with Mounting Base Albright International Ltd, Evingar Trading Estate, Ardglen Road, Whitchurch, Hampshire, RG28 +44 UK Albright International, 125 Red Lion Road, Surbiton, Surrey KT6 7QS, England,Tel: +44 (0) 20 8390 5357, Fax:7BB,(0) 20 8390 1927 Tel: [email protected] or [email protected] Web 890030, Fax: +44 (0)1256 890043 E-mail: +44 (0)1256 893060, Fax: +44 (0)1256 893562, Dedicated Sales Tel: +44 (0)1256 Site: www.albrightinternational.com E-mail: [email protected] or [email protected] Web Site: www.albrightinternational.com Copyright © 2010 Albright International Ltd Copyright © 2013 Albright International LTD

PC60 Single Pole Single Throw Normally Open Mounting Boards All configurations of the PC60 can be supplied with an optional separate mounting base which can be soldered to the circuit board. After soldering and washing the printed circuit board, the PC contactor can be plugged into the base and secured by means of an M4 nut on the underside of the board. Removal for servicing or replacement is possible by removal of the nut and unplugging the PC contactor from the base. PC60 with Mounting Base Technical Drawing RED POSITIVE LABEL HERE WHEN - MAGNETIC BLOWOUTS FITTED COIL PINS- SECURING CONTACTOR...