video corpo

Rotorseal and Quick Release Valves
10Pages

{{requestButtons}}

Catalog excerpts

Rotorseal and Quick Release Valves - 1

Controls and Air Tank Groups Section J EATON Airflex® Clutches & Brakes 10M1297GP November 2012

Open the catalog to page 1
Rotorseal and Quick Release Valves - 2

Flow control valve 1/2, 3/4 & 1-1/2 NPT. Airflex® Standard Air Tank Group Section J Pressure Switch Typically set at 90 p.s.i. so clutch will diseng when supply air pressure drops below this s Use normally open contacts. Pressure Switch Bushing Pressure Gauge Pipe Elbow Flow control valve 1/2, 3/4 & 1-1/2 NPT. Note: Locate complete air tank within 5 feet of the rotorseal. Consult factory when locating air tank at greater distances. Pipe Nipple Fiber Coupling Hose Assembly Set at min p.s.i. 1.5 to 5 and interlock with motor starter so motor cannot be started with clutch engaged. Use normally...

Open the catalog to page 2
Rotorseal and Quick Release Valves - 3

Rotorseals and Rotorseal Assemblies Section J Pipe Size Rotorseal Group Size Inlet Thread Rotorseals shown are for typical arrangements only. EATON Airflex® Clutches & Brakes 10M1297GP November 2012

Open the catalog to page 3
Rotorseal and Quick Release Valves - 4

Clutch Applications Air Tank Groups Section J Airflex offers a complete line of air tank group (ATG) packaged solutions to suit complete clutch application air supply requirements. This new line of ATGs are ruggedly designed for harsh environments such as grinding mills and oilfield applications. The ATGs come with a complete air supply system including: a filter, pressure regulator, air receiver tank, Size Single Narrow Dual Narrow Single Wide Dual Wide solenoid valve, flow control valve, and pressure switches. Each solution is specially packaged for convenient on site assembly. Premium...

Open the catalog to page 4
Rotorseal and Quick Release Valves - 5

Airflex Standard Electrical Controls Airflex® Standard Electrical Controls for Grinding Mills Section J Customer’s Starter Interlock (See note 2) Pressure Switch To Customer’s Equipment FED from Customer’s Power Source Enclosure for Standard Panel Normal mill starting procedure is to bring the motor up to operating speed and then engage the clutch to accelerate the mill. Airflex offers a simple, but very reliable system for clutch control. The system consists of two parts: the pneumatic and electrical portions. A pressure actuated limit switch prevents the motor from starting if air...

Open the catalog to page 5
Rotorseal and Quick Release Valves - 6

Custom Solutions Engineered to Last World Class, Airflex® Worldwide Slip Detection Control for Grinding Mills Eaton supports Airex® Section J with distributor products Eaton combines 70 years of industrial clutch and brake experience with ground breaking, innovative and proven product designs to locations in over 65 countries worldwide. Parts, experienced sales engineers and instant access also offers a unique clutch slip detection conAirflex®to Eaton’s power application solutions you can transmission knowledge base trol manufacturing resources for grinding mill products and which provides...

Open the catalog to page 6
Rotorseal and Quick Release Valves - 7

Hydraulic Inching Drives for Grinding Mills Air Tank Group Selection Section J Portable – single point lift system Extends clutch life – reduces maintenance costs Simple controls and connections – faster maintenance Eaton’s expertise in Hydraulic Drives has enabled customer specic solutions to beto be realized Eaton’s expertise in Hydraulic Drives has enabled customer specic solutions realized Eaton’s expertise in Hydraulic Drives has of these innovations introduction of Hydraulic Inching in manymany industries. latestlatest enabled customer is theis the introduction of Hydraulic Inching in...

Open the catalog to page 7
Rotorseal and Quick Release Valves - 8

Hydraulic Power Unitfor Hydraulic Power Hydraulic Power UnitUnit Inching Drive Section J Providing power to theDrive Drive System, the Hydraulic Unit Providing power Drive System, the Hydraulic Power Providing power to theto the System, the Hydraulic PowerPower Unit has an Eaton® Hydrostatic Transmission Pump close closecou- to to has an Eaton® Hydrostatic Transmission Pump coupled Unit has an Eaton® Hydrostatic Transmission Pump close coupled the to the motor. The reservoir is sealed and lled only only the electric motor. The reservoir is sealed and filled pledelectricelectric motor. The...

Open the catalog to page 8
Rotorseal and Quick Release Valves - 9

Drive System Drive Section J System The Industrial planetary style torque multiplier with hydraulic The Industrial planetary style torque multiplier with hydraulic motor drive input turns the pinion shaft at the required speed. motor drive input turns the pinion shaft standard and can be Automatic torque overload protection isat the required speed. adjusted as needed from the operatoris standard and can be Automatic torque overload protection control station. The automatic brake canfrom the operatoror released as desired adjusted as needed be manually set control station. The for...

Open the catalog to page 9
Rotorseal and Quick Release Valves - 10

Features and Benefits for Inching Drive Section J • Torque range up to 785,000 lb.ft (1,070,000 Nm) • Sealed reservoir ensures long service life temperature, and optional mill position (position feedback • Standard filtered reservoir fill system with suction wand • Maximum torque limiting built into the hydraulic pump • Power supply cable with receptacle makes startup quick operator complete control • Precision Electric Joystick controller ensures accurate • Precision Electric Joystick controller ensures accurate positioning and saves time • Mechanical and electrical interlocks life •...

Open the catalog to page 10

All Airflex catalogs and technical brochures

  1. CB Tech Specs

    40 Pages

  2. AMCB 16200

    8 Pages

  3. CB

    40 Pages

  4. Overview

    15 Pages

  5. CBC Tech Specs

    12 Pages

Archived catalogs