Temperature • These reasonably priced sensors are for universal use (-200 to +1100 °C) and suitable for immersion measurements in liquids, air, and gases. The sheathed line, depending on diameter, can be bent - within certain limits. • Different connection variants: With cable and ALMEMO® connector Order no. FxAxx, with cable and free ends, Order no. Fx0xx. Connector options: With THERM circular connector: Option T9020RS, with miniature Thermo flat connector: Option OT9020FS. Thermocouple sheathed sensors FTAxx and FTANxx Accuracy: Sensor tip, sheathed line: Cable sleeve: Standard cable: Cable options: ALMEMO® connector: FTAxx; NiCr-Ni thermocouple, type K, DIN class 1* FTANxx; NiCrSi-NiSi thermocouple, type N, DIN class 1* diameter, length, operating temperature; see table; material Inconel 2.4816 Here the sensor tip and sheathed line are of the same diameter. These types are therefore also suitable for mounting with clamped screw connections. Brass, hexagonal, L = 65 mm, circumdiameter = 9 mm, operating temp. –40 to +160 °C 1.5 meter FEP / silicone thermal line (stranded wire)* Operating temp. -50 to +200 °C There is no adverse temperature effect at the juncture from measuring element to cable. Compensation line, PVC / PVC, insulated, operating temperature –20 to +105 °C The compensation line is also available, on request, with FEP / FEP, insulated. FTAxx NiCr-Ni ZA9020FS with resolution 0.1 K FTANxx NiCrSi-NiSi ZA9021FSN with resolution 0.1 K Pt100 sheathed sensors FPAxx Accuracy: Options: Sensor tip: Sheathed line: Cable sleeve: Standard cable: Cable options: ALMEMO® connector: Pt100 film resistor, DIN class B* DIN class A, 1/5 DIN class B Pt100 wire wound measuring resistor diameter, length, operating temperature; see table; material stainless steel diameter, length; see table; material stainless steel On certain types the sensor tip and sheathed line are of different diameter; (i.e. the sensor tip is thicker). These types are therefore not suitable for mounting with clamped screw connections. Types suitable for clamped screw connections are available on request. Brass, hexagonal, L = 65 mm, circumdiameter = 9 mm, operating temp. –40 to +160 °C 1.5 meters line, FEP / silicone, insulated, operating temperature –50 to +200 °C Line, PVC / PVC, insulated, operating temperature –20 to +105 °C The line is also available, on request, with FEP / FEP, insulated. Pt100, ZA9030FS1, with resolution 0.1 K Option: Pt100 ZA9030FS2 with resolution 0.01 K (standard with 1/5 DIN class B) NTC sheathed sensors FNAxx Accuracy: Sensor tip: Sheathed line: Cable sleeve: Standard cable: Cable options: ALMEMO® connector: NTC type N (see beginning of chapter) diameter, length, operating temperature; see table; material stainless steel diameter, length; see table; material stainless steel On certain types the sensor tip and sheathed line are of different diameter; (i.e. the sensor tip is thicker). These types are therefore not suitable for mounting with clamped screw connections. Types suitable for clamped screw connections are available on request. Brass, hexagonal, L = 65 mm, circumdiameter = 9 mm, operating temp. –40 to +160 °C 1.5 meters line, PVC / PVC, insulated, operating temperature –20 to +105 °C Line, FEP / silicone, insulated, operating temperature –50 to +200 °C The line is also available, on request, with FEP / FEP, insulated. NTC, ZA9040FS, with resolution 0.01 K. * Range of validity see beginning of chapter ** No temperature influence at the transition from the measuring element to the cable (see beginning of chapter) DAkkS accredited calibration or factory calibration KT90xx temperature for sensor or measuring chain (sensor + device), see chapter „Calibration certificates“. DAkkS accredited calibration meets all the requirements regarding test resources laid down in DIN EN ISO/IEC 17025. 11/2025 • We reserve the right to make

Temperature Sensor with: Sensor tip, dimensions d1, sheathed line, dimensions d2, overall length (including sensor tip) L, Cable sleeve, dimensions length = 65 mm, circumdiameter = 9 mm, Cable 11/2025 • We reserve the right to make technical changes. Connection cable DAkkS accredited calibration or factory calibration KT90xx temperature for sensor or measuring chain (sensor + device), see chapter Calibration certificates^ DAkkS accredited calibration meets all the requirements regarding test resources laid down in DIN EN ISO/IEC 17025.

* This sensor type (reinforced tip) is not suitable for clamped screw connections. Suitable types FPA20Lx or FPA30LX with same end-to-end diameter are available on request. ** Too strongbending of / kinking of the sheathed line should be avoided. 11/2025 • We reserve the right to make technical changes. Accuracy class B default Accuracy class 1/5 DIN Class B* OPG5 Wire-wound measuring resistor operating range -100 ... 450 °C OPM1 DAkkS accredited calibration or factory calibration KT90xx temperature for sensor or measuring chain (sensor + device), see chapter Calibration certificates^ DAkkS accredited...

Temperature Handle for sensors with hexagonal cable sleeve Option Handle including fitting Clamp srew connection ZT943xKV Operative range For sheath elements Option: Notched steel ring (once fitted, cannot be removed) Tmax = 800 °C For ZT9431KV Order no. OT9431ST For ZT9432KV Order no. OT9432ST Variants (with PTFE clamping ring) for types FTA15Lxxxx, FPA16Lxxxx for types FTA30Lxxxx, FPA30Lxxxx and FNA30Lxxxx Technical data Operating temperature Thread up to maximum 250 °C with option up to 800 °C M8x1, 13 AF 11/2025 • We reserve the right to make technical changes. For surface measurement, operative...

Temperature Accuracy: NiCr-Ni class 1* Measuring tip: Operative range -200...+1100 °C 200 x 1.5 mm, sheathed line, Inconel T90*: 1.5 s Cable: 1.5 m FEP/silicone thermal line** with ALMEMO® connector L = 200 mm (No variants available) Option: Handle mounted Pt100-sensor FPA 32 P1 Accuracy: Pt100 film resistor, class B* Measuring tip: Operative range -40...+400 °C 200 x 2.8 Measuring tip reinforced 3.2 mm, sheathed line stainless steel T90*: 10 s Cable: 1.5 m PVC / PVC with ALMEMO® connector For immersion measurement L = 200 mm (No variants available) Option: Handle mounted NTC-sensor FNA 305 Accuracy:...