1. Catalogs
  2. Ahlborn Mess- und Regelungstechnik GmbH
  3. Flow sensors for liquids in stainless steel FVA 645-GVxQT5

Flow sensors for liquids in stainless steel FVA 645-GVxQT5

Flow sensors for liquids in stainless steel FVA 645-GVxQT5

Product catalog summary
Overview: The FVA 645-GVxQT5 is a stainless steel flow sensor designed for liquid measurement without any moving parts. It includes integrated temperature measurement and is suitable for systems with laminar flow, no pressure surges, air pockets, or suspended solids.
Key Features:
  • Stainless steel construction with no moving parts.
  • Integrated temperature measurement.
  • Low pressure loss and wide temperature range.
  • High-speed reaction time.
  • Suitable for water and heat output measurement in heating and cooling systems.
Measuring Principle: Utilizes pressure pulsation and Kármán vortex street for flow measurement.
Flow Measurement:
  • Accuracy: ±1.5% of final value using water at 0 to +100°C.
  • Reaction time: Less than 3 seconds for 63% of the final value.
Temperature Measurement:
  • Range: 0 to +100°C.
  • Accuracy: ±1 K at +15 to +90°C, ±2 K at 0 to +100°C.
  • Resolution: 0.1 K.
  • Reaction time: Less than 0.25 seconds under flow conditions for 50% of the final value.
Process Connection: Available with 2x male thread connections, specifics vary by variant.
Pressure and Conditions:
  • Pressure: 10 bar.
  • Pressure loss: 0.1 bar typical under flow conditions.
  • Suitable for water with viscosity < 2 mm²/s and conductivity >2 µS/cm.
  • Temperature of medium: 0 to +100°C.
  • Ambient temperature: -25 to +60°C.
  • Ambient humidity: Up to 95% RH, non-condensing.
Electrical Connections:
  • Output signal: 2x 0.5 to 3.5 V (4.1 V).
  • Power supply: 5 VDC (±5%), <10 mA via ALMEMO® connector.
  • Connection: Sensor with 2.9-meter connecting cable and ALMEMO® connector.
Materials: Corrosion-resistant coating with EPDM, PPS, PPA 40-GF, and stainless steel 1.4408.
Calibration: DAkkS accredited calibration KV91xx for flow, fulfilling DIN EN ISO/IEC 17025 requirements.
Variants: Available in different measuring ranges and fitting lengths:
  • 1 to 18 l/min, G 3/4" male thread, 110 mm length.
  • 2 to 40 l/min, G 3/4" male thread, 110 mm length.
  • 5 to 100 l/min, G 1" male thread, 129 mm length.
  • 10 to 200 l/min, G 1 1/4" male thread, 137.5 mm length.
Note: The sensor must be directly connected to an ALMEMO® device and cannot be used with extension cables.
See more

Catalog excerpts

Flow sensors for liquids in stainless steel FVA 645-GVxQT5-1

• Measuring section in stainless steel • Application in systems with laminar flow, no pressure surges, no air pockets, no suspended solids • Without any moving parts • Integrated temperature measuring • Wide temperature range • High-speed reaction time • Using with water • For heat output measurement in heating systems and cooling plant Measuring principle Pressure pulsation Karman vortex street Measuring range see variants Accuracy using water as medium at 0 to +100 °C ±1.5 % of final value Resolution see variants Measuring range 0 to +100 °C Accuracy ±1 K at +15 to +90 °C Reaction time (63 %) <0.25 second under flow conditions 50 % of final value Process connection 2x male thread see variants Pressure loss 0.1 bar, typical under flow conditions, Suitable conditions Media Water, Viscosity < 2 mm2/s) and conductivity >2 pS/cm Temp. of medium 0 to +100 °C Ambient temperature -25 to +60 °C Ambient humidity up to 95 % RH, non-condensing Electrical connections Output signal 2x 0.5 to 3.5 V (4.1 V) via ALMEMO® connector Connection Sensor with 2.9-meter connecting cable and ALMEMO® connector Fitting length see variants Materials (in contact with media) Corrosion-resistant coating EPDM, PPS, PPA 40-GF Pipe piece Stainless steel 1.4408; 11/2026 • We reserve the right to make technical changes. ! Note: The sensor can only be operated by plugging DIRECTLY onto an ALMEMO® device. (NOT with extension cables ZA9060VKx or ZA9090VKCx). Variants Sensor for flow rate and temperature over a measured section, including ALMEMO® connecting cable, 2.9 meters Measuring range ALMEMO® Process connection Fitting length Order no. G 3/4“ male thread G 3/4“ male thread G 1“ male thread G 1 1/4“ male thread DAkkS accredited calibration KV91xx, flow, for probes, see chapter „Calibration certificates“. The DAkkS accredited calibration fulfills the requirements of DIN EN ISO/IEC 17025 for test equipment.

 Open the catalog to page 1

All Ahlborn Mess- und Regelungstechnik GmbH catalogs and technical brochures

  1. ALMEMO® 2470

    3  Pages

  2. ALMEMO® 2890

    2  Pages

  3. ALMEMO® 104

    3  Pages

  4. ALMEMO® 710

    3  Pages

  5. ALMEMO® 510

    3  Pages

  6. ALMEMO® 809

    2  Pages

  7. ALMEMO® 5690

    8  Pages

  8. ALMEMO® 1020

    2  Pages

  9. ALMEMO® 1030

    2  Pages

  10. ALMEMO® 1033

    2  Pages

  11. ALMEMO® 1036

    2  Pages

  12. ALMEMO® 8036

    3  Pages

  13. RTA5

    1  Page

  14. RTA6

    1  Page

  15. Cases

    1  Page

  16. WinControl

    13  Pages

  17. OPC export

    4  Pages

  18. ODBC

    4  Pages

  19. Web server

    4  Pages

  20. PIMEX

    4  Pages

  21. CAN Trace

    4  Pages

  22. Thermo-wires

    3  Pages

  23. FHAD 36 Rx

    4  Pages

  24. FHA 646 R

    1  Page

  25. FHAD46-7

    1  Page

  26. Psychrometer

    1  Page

  27. MH8D46

    2  Pages

  28. Pitot Tubes

    2  Pages

  29. Force

    3  Pages

  30. Displacement

    2  Pages

  31. Vibration

    2  Pages

  32. Speed

    1  Page

  33. Flow

    2  Pages

  34. Wind sensor

    2  Pages

  35. Comfort Index

    2  Pages

  36. Sound Level

    1  Page

  37. Moisture

    5  Pages

  38. Tensiometer

    1  Page

  39. FLAD03VL1

    1  Page

  40. FLA623

    3  Pages

  41. VLambda

    1  Page

  42. Luminance

    1  Page

  43. pH

    4  Pages

  44. Conductivity

    2  Pages

  45. CO sensor

    1  Page

  46. Certificates

    8  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.
About DirectIndustry
DirectIndustry is a marketplace that offers B2B players a complete experience, from product sourcing to purchase. DirectIndustry is an entity of VirtualExpo Group.