Air flowDigital vane anemometer FVAD 15-Hfor special applications, with ALMEMO® D6 plug -H16GFAMC40 Technical data and functions • The precision measuring heads and the sensor shaft are made of aluminum or stainless steel. • The flow velocity is measured with high accuracy. • Each vane anemometer is individually adjusted. The Multipoint adjustment is stored in the ALMEMO® D6 connector. • In practice, measurements in air and gases are unaffected by environmental variables such as pressure, temperature, or humidity. The low dependence of the measured value on density of the gas can be compensated for. The density can be programmed in the ALMEMO® D6 sensor menu in the ALMEMO® V7 device. Nominal conditions 22 °C ±2 K, 1013 mbar Connecting cable permanently fitted cable, with Lemo plug ALMEMO® adapter cable Lemo coupling cable, with ALMEMO® D6 plug Frequency measurement resolution 0.01 Hz Variant: Micro, aluminum, Measured medium: water Operative range: -20 to +100 °C (including cable) Pressure resistance: up to 3 bar overpressure Measuring range: in water: 0.06 to 10 m/s Accuracy: ± (+0.5 % of final value sensor + 1.0 % of measured value) specific multi-point adjustment Type of rotating vane: MC40GFA, aluminum Measuring head: • Several measuring heads can be used for measurements in water. • Some variants detect the direction of flows and display the measured value with an algebraic sign. • The robust type of construction is suitable for mobile measuring operations as well as for stationary measuring operations. • The ALMEMO® D6 plug measures the frequency signal of the rotating vane with high resolution. • 1 measuring channel is preprogrammed (ex works): Flow velocity (m/s, v). Multi-point adjustment sensor specific, saved within the ALMEMO® D6 plug of the adapter cable Refresh rate 0.5 seconds for all channels Averaging period 2 seconds, programmable from 2 General features for the ALMEMO® D6 sensors: see chapter ALMEMO® Measuring instruments Sensor shaft: Aluminum, 0 16 mm Sensor length: 163 mm (dimension C) Cable exit: Thread M 14 x 1.5 (dimension IG) ! New from 11/2023 for impeller for water: Supplied with factory calibration certificate (mandatory): Calibration with medium water at 6 calibration values in the measuring range of the sensor, incl. multi-point adjustment of the sensor. 11/2025 • We reserve the right to make technical changes. Accessories Order no. Extension set 0 16 mm, stainless steel, 3 pipes 350 mm each. 3 O-rings (material: FPM75) ZV9915H16VR3 Other accessories: see digital humidity / temperature transmitter MH8D46C Digital vane anemometer for water, up to 10 m/s (water), up to 100 °C, integrated fixed cable, adapter cable with ALMEMO® D6 plug. Incl. factory calibration certificate (mandatory) with medium water. FVAD15H16GFAMC40 DAkkS accredited calibration or factory calibration KV90xx, air flow, for digital sensor, see chapter „Calibration certificates“. DAkkS accredited calibration meets all the requirements regarding test resources laid down in DIN EN ISO/IEC 17025.

Air flow Digital vane anemometer with direction detection FVAD 15-H25RGAMN40 Digital vane anemometer FVAD 15-H25RGAMN40 Technical data Measured medium: Operative range: Pressure resistance: Measuring range: Type of rotating vane: Mini, aluminum, with integrated direction detection air and gases -20 to +125 °C (including cable) up to 6 bar overpressure ± 0.4 to ± 40 m/s with direction detection ± (+0.5 % of final value sensor + 1.0 % of measured value) specific multi-point adjustment MN40GA, aluminum Measuring head: Sensor shaft: Sensor length: Cable exit: Cable length: Aluminum, 0 25 mm dimension...

Digital vane anemometer, operating range up to 260 °C FVAD 15-H25GEMN40T2 Technical data Variant: Measured medium: Operative range: Pressure resistance: Measuring range: Accuracy: Type of rotating vane: Mini, stainless steel, Measuring head: -40 to +260 °C (including high-temperature cable) Sensor shaft: up to 10 bar overpressure Sensor length: ± (+0.5 % of final value sensor Cable length: + 1.0 % of measured value) specific multi-point adjustment MN40GE, stainless steel stainless steel, 0 25 mm dimension C 81 mm dimension A 0 18.2 mm dimension B 14 mm stainless steel, 0 25 mm 170 mm (dimension...