CURVES WITH MINIMUM RADIUS

EUROBELT modular conveyor belts are manufactured with technical plastics forming a structure of interlocking injection molded parts in an advanced design whose configuration makes them the ideal support for the transport of food and industrial products. Their modular configuration allows the belt to be made to measure according to the needs.

SERIES E925 FLUSH GRID Minimum radius = Belt width (mm) x Factor With tab, the width of the belt will always be referred to the useful surface of the belt, without taking into account the tabs. Belt nominal width (mm) Clip-on rod retention system 0 6 mm with cut-outs on both sides Standard rod dimensions: - Multiples of 20 mm - Minimum 100 mm - Maximum 700 mm

SPROCKETS ACCESORIES - SPROCKETS N° of teeth 0 Pitch Bore for square shaft Hub width Round shaft (max) mm inch. with keyway without keyway Standard material: Polyacetal SPROCKETS FOR ROUND SHAFT We also offer sprockets for use with Drum Motors in applications where special cleanliness is required or for conveyors where it is impossible to position the motor externally due to space or safety problems. SPROCKET INSTALLATION Fully rounded edges for easy cleaning. Chamfered teeth on the sides to facilitate entry into the belt and prevent skipping. Open holes that allow water to pass between gears...

CLE RETENTION RING These rings are placed on both sides of the central gear to fix it to the shaft, preventing lateral belt displacements. They are fixed by means of a set screw embedded in the ring itself. 1 gear must be placed in the centre, held in place by 2 CLE retaining rings at the ends. Then place the same number of gears on each side of the central gear, without any type of fastening, in order to absorb possible expansions and contractions of the belt. The same action must be taken on both shafts. STAINLESS STEEL AISI 316. High working temperature range. For 40 mm, 1 1/2" 60 mm or 2...

To make the fastening and the support of the belt, EUROBELT offers two types of hold-down profiles with different geometries. These profiles, with a low coefficient of friction, are placed between the belt and the structure of the conveyor, reducing the wear of the surfaces in contact, which contributes to prolong the life of the belt. EUROBELT offers all the hold-down profiles in special polyethylenes with very good sliding properties and an excellent resistance to impact.

INSTALLATION OF PROFILES AND PLATES HEAD END 40 MM WITHOUT TAB (SL40) < 30 The clamping shall be carried out on the top of the belt. The clamping profiles shall not be in contact with the belt. WITH ONE L-PROFILE AND ONE U-PROFILE INSTALLATION OF PROFILES AND PLATES HEAD END 40 MM WITH TAB (SL40) < 25 The fastening shall be above the tab and shall be free from interference with the product transport. The clamping profiles shall not be in contact with the belt. WITH ONE L-PROFILE AND ONE U-PROFILE INSTALLATION OF PROFILES AND PLATES HEAD END 40 MM WITH TAB (SL40) It is recommended to cover the...

The following formula was used to calculate the minimum number of gears required on both the drive and driven axles: Belt width (mm) Minimum quantity =- Belt nominal width (mm) (1) Check if it is necessary to fit more gears. The quantity must always be odd. When calculating the number of supports, the weight of the product to be transported must be taken into account. The distance between supports on the transport route must not exceed 150 mm, and 300 mm on the return.

CONSTRUCTION DATA - HORIZONTAL CONVEYOR Z12 98,56 mm 42 47 96 [A] Distance between the sliding surface of the belt and the centre of the shaft. [B] Distance between the vertical of the shaft and the start of the sliding surface. [C] Distance between the sliding surface of the belt and the support of the return. [D] If gears are used on the inflexion shaft, do not retain the centre one. [R] This radius should be as large as the application allows in order to minimise wear (min. 150mm). On belts with side fins refer to this radius. A - The minimum length of the first straight section shall be 1,5...

MATERIALSMATERIALSSTANDARD POLYPROPYLENE (PP)STANDARD POLYACETAL (AC) Base material for the manufacture of conveyor belts for most processes, both in the food and industrial sectors. With good mechanical strength, a temperature range of +5 °C to +104 °C, and a specific weight of 0.9, it has buoyancy in water. Its excellent chemical resistance to practically all acids, concentrated bases, salts and detergents makes it indispensable in corrosive working environments. It is highly resistant to penetration by micro-organisms. Although it has an impact resistance of about 3.5 kJ/m2, below a temperature...

METAL AND X-RAY DETECTABLE 51 EU 10/2011 «i"pnoviO FDA CFR title 21 by FCN1847 Used in belts for process lines where you want to avoid that it can be mixed with the product, pieces or splinters of the same. Material easily detectable by all types of metal and X-ray detectors. It is advisable to test the material in your production environment to determine the detection sensitivity of your equipment. Suitable for direct contact with foodstuffs. LIMITATION OF LIABILITY EUROBELT elements are guaranteed for a period of one year from the date of shipment with respect to the repair or substitution...