TC
11Pages

wm '****■ ^^ $ High quality # for the success of your pharmaceutical process PRODUCT Stainless Steel fittings comply with ASME BPE standards. All clamp gaskets compounds meet the criteria of the FDA, and some compound formulations have also been certified and accepted by the USDA, 3-A Sanitary Standard, and USP Class VI certifications. Fittings are fabricated in AISI 316L Stainless Steel (EN 1.4404 - 1.4435). Sulfur controlled to 0,005 @ 0,017% on all weld ends, allowing for consistent and high quality orbital welding process. Sulfur has the biggest impact on weld quality. SIZES...

Final tolerances for mechanically polished fittings and process components Nominal Size GENERAL NOTE: tolerances on E end-to-end, center-to-end: 1,27 mm. The length of the control portion C is fixed for all size at 19 mm GENERAL NOTE: All Ra readings are taken across the lay, wherever possible. The average Ra is derived from readings taken at four cross sections rit 'if approximately 90 ° apart. No single reading exceeding Ra max.

Clamp in misura unica - One size accomodates ¥2” and % Clamp a due settori con doppio snodo - Double pin heavy duty clamp Size 1” @ Le pressioni max riportate in tabella si basano su risultati ottenuti da prove idrauliche utilizzando guarnizioni standard in Buna-U. Per temperature superiori a 121 °C si raccomanda di utilizzare solo il clamp tipo 13MHP. Service rating are based on hydrostatic tests using standard Buna-U gaskets. For temperature above 121 °C we recommend using only 13MHP clamp only

ASME BPE-2002 compliant BPE TABLE # DT-22 code L14AM7 code 14WLM0 code 14WLMP code 14MPW size Tronchetto a saldare corto - Short Welding Ferrule size A B Tronchetto a saldare per orbitale - Orbital welding Ferrule Tronchetto a saldare per orbitale - Orbital welding Ferrule Tronchetto a saldare lungo - Long Welding Ferrule (Light) Tronchetto a saldare spessorato - Welding Fer

size ABC code 2CMP - 90° ELL Curva clamp 90° - 90°Elbow clamp ends Cod. B2KMP-45° ASME BPE-2002 compliant BPE TABLE # DT-17 code 2KMP - 45° ELL Cod. B7MP ASME BPE-2002 compliant BPE TABLE # DT-18 Cod. B7RMP ASME BPE-2002 compliant BPE TABLE # DT-19 Tee clamp - Tee clamp ends size A B Tee clamp ridotto - Reducing tee clamp ends 1 size A B

code 16AMP Tappo clamp cieco - Clamp solid end cap code 31-14MP Riduzione concentrica clamp - Concentric reducer clamp ends BSPP/CYLINDRICAL GAS THREAD PROFILE size A Riduzione eccentrica clamp - Eccentric reducer clamp ends Adattatore femmina - Female adapters (non 3A) size code Adattatore maschio - Male adapters (non 3A) BSPT/CONICAL GAS Thread profile BSPP/Cylindrical gas BSPT/Conical gas NPT B= ON REQUEST

Sanitary Clamp Gaskets All clamp gaskets compounds meet the criteria of the FDA, and some compound formulations have also been certified and accepted by the USDA, 3-A Sanitary Standard, and USP Class VI certifications. codice materiale tipo FRACTIONAL Tipo piu comunemente usato ed economico. E disponibile da W a 12". Standard-Molded, one piece O-ring Gasket is economical, dependable. Available from stock te” 12". cod. 40MP Guarnizione standard in un solo pezzo tipo economico Tipo flangiato per essere tenuto in posizione. E disponibile da 1" a 12". Flanged-Molded, flanged O-ring...

Guarnizioni prodotte in quattro versioni base in una varieta di materiali atossici, non igroscopici. Gaskets are produced In four basic designs in a variety of materials that are non-toxic, absorbent free. ■ Meet U.S. Pharmacopoeia Class VI ■ Comply with title 21 CFR 177.2600

ASME BPE-2002 COMPLIANT FITTINGS available on request Cod. B2S- 90 ° ASME BPE-2002 compliant BPE TABLE # DT-7 Cod. B2KS- 45 ° ASME BPE-2002 compliant BPE TABLE # DT-8 Cod. B7WWW ASME BPE-2002 compliant BPE TABLE # DT-9 code 7WWW Weld ends fitting size Curva saldare 90 ° - 90 °Elbow weld ends Curva saldare 45 ° - 45 °Elbow weld ends

Cod. B7RWWW ASME BPE-2002 compliant BPE TABLE # DT-10