ISO 6431 SERIES Cylinder Mount & Stand Alone

FEATURES 1 BODY Solid aluminum precision machined for accurate alignment. Black anodized for appearance and corrosion resistance. 2 LOCKING MECHANISM Oversized, hardened and ground locking with antifriction amplification. No Rod Displacement on Engagement Large Clamping Surface Fast Response Time Extremely Low Backlash Spring Engaged Units Profile Matches ISO 6431 Cylinder 4 bar (60 PSI) release pressure Precision Holding (.05 - .08 mm) Consistent Clamping Force High Cycle Rates and accuracy Holds Load During Power/Pressure Loss Compact Unit, Easy Integration Broad Applications 3 COIL SPRINGS...

This new ISO 6431 - Style AMLOK® Pneumatic Series RLI Rod Clamp has been developed as a solution to control problems inherent to pneumatics —over travel, drifting, bouncing and reverse traveling. The AMLOK® Power-Off Rod Clamp can be mounted to the ISO 6431 cylinder of your choice, or as a stand alone unit to be used with no cylinder at all. The AMLOK® has been designed with oversized components to withstand the most severe applications. For example, the contact area of the clamping collet is considerably greater than on similar units. The increased contact area reduces the pressure-per-square-inch...

The new AMLOK® RLI Series Rod Lock design can be sealed. Suitable for food and washdown applications. Other common applications include: Machine Tool Applications Scissor-lift Tables Test and Positioning Equipment Amusement Ride Equipment Printing and Paper Handling Equipment Theatrical Equipment (Platforms) Assembly and Test Equipment AMLOK ® RLI attached to ISO 6431 cylinder with optional prox switch.

ASSEMBLY INSTRUCTIONS RLI ASSEMBLY INSTRUCTIONS 1. Read Assembly Instructions and Caution Label on unit. 2. Connect a flexible hose to the pressure port of the AMLOK®, apply air pressure to release the clamping mechanism and slide the AMLOK® over the rod to be clamped. 3. Align the mounting holes and release port hole to the proper location. 4. Release pressure 60 PSI clean, dry, compressed air. 5. Bolt AMLOK® to cylinder or housing. 6. Pressurize the AMLOK® to the specified release pressure. 7. Release and pressurize several times. With the specified pressure the rod should move freely through...

PROXIMITY SWITCH The new RLI ISO 6431 series Amlok provides for optional proximity switch. Specifications for optional proximity switch (indicates ‘unclamped’ position) WIRING CONNECTIONS PNP normally open PROXIMITY SWITCH SETTING INSTRUCTIONS 1. Set the AMLOK® to the unclamped ‘pressure applied’ position. 2. Screw the proximity switch (with jam nuts) into the designated M 8 x 1 proximity switch hole, until it makes contact. 3. Unscrew (back off) the proximity switch approximately 3/4 turn. While holding the proximity switch in the set position, tighten the locking nut using 6 ft/lbs (8 NM) of...

STANDARD SPECIFICATIONS • ISO 6431 Mounting Styles • One Piece Solid Body Design • Maximum Operating Pressure - 160 PSI Air (11 bar) Required Release Pressure - 60 PSI Air (4 bar) Operating Media - Clean, Dry, Filtered, Compressed Air • Operating Temperature - Standard 10°F to + 180°F (-12°C to +82°C) - Optional 10°F to + 250°F (-12°C to +121 °C) • Holding Force - Axial holding forces were established after 2,000,000 fatigue test cycles • Minimum linear movement may occur after clamp is fully engaged (.05mm - .08mm) ROD LOCK OPERATION SPECIFICS • Holds with consistent force in both directions •...

AMLOK ROD CLAMP TECHNICAL DATA AMLOK Type - RLI * Stand-alone unit contains wipers and rod bearings on each end.

CMXO : Cylinder Mount Rod lock housing contains 4 through holes. Kit contains: 1 Rod Lock 4 Hex Nuts 4 Tie Rods Kit contains: 1 Rod Lock 1 Angle Bracket 4 Hex Nuts 4 Tie Rods Assembly contains: 1 Rod Lock 2 Angle Brackets 2 Tie Rods 4 Hex Nuts SMF1 : Stand Alone CMF1 : Cylinder Mount SA / CA : Stand Alone Assembly contains: 1 Rod Lock 1 Front Flange 1 Rear Flange 8 Hex Nuts 4 Tie Rods SMF1 Assembly and CMF1 Kit contain: 1 Rod Lock 1 Front Flange 4 Tie Rods 8 Hex Nuts MOUNTING DIMENSIONS MXO / SN - STAND ALONE No mounting hardware included

MOUNTING DIMENSIONS CMXO - CYLINDER MOUNT RLI - XXX XXX CMXO PART NUMBER ROD Dia. BORE Dia. B [mm] WEIGHT [LBS] CYLINDER MOUNT Front Flange Mount - CMXO (NFPA Style MS1) Ships as a kit MOUNTING DIMENSIONS CMSi - CYLINDER MOUNT RLI - XXX XXX CMS1 CYLINDER MOUNT Front Flange Mount - CMS1 (NFPA Style MS1) Ships as a kit PART ROD BORE AB AH NUMBER Dia. Dia. [mm] [mm] MOUNTING DIMENSIONS SMSi - STAND ALONE RLI - XXX XXX SMS1 X XX STAND ALONE Front Flange Mount - SMS1 (Style MS1) Ships assembled

MOUNTING DIMENSIONS SA / CA - STAND ALONE STAND ALONE Front Flange Mount (NFPA Style MF1 and MF2) Ships assembled Includes rod bearings and wipers on both ends. PART ROD BORE B E F FB L R TF UF NUMBER Dia. Dia. [mm] [mm] [mm] Dia. [mm] [mm] [mm] [mm] MOUNTING DIMENSIONS SMFi AND SMF2 - STAND ALONE PART NUMBER ROD BORE B DD E F FB L R STAND ALONE Front Flange Mount - SMF1 (Style MF1) Ships assembled Rear Flange Mount - SMF2 (Style MF2) Ships assembled MOUNTING DIMENSIONS CMFi / CMF2 - CYLINDER MOUNT part NUMBER ROD BORE B BB DD...

YOUR ONE SOURCE SOLUTION FOR MACHINE TOOL COMPONENTS J? SPINDLE SHAFTS COMPONENTS HSK TOOLS *?CHIP CONVEYORS.. CHIP DISC PITERSSTEEL WAYCWERS M. ADVANCED Mm MACHINE A ENGINEERING CO. Innovative People, Products and Processes At AME, innovation is part of our culture. You can see the result in our processes, partnerships, people and services — and in the precision engineered components, machines and services showcased here. Learn more about AME and our innovative approach to precision machining, call 815-962-6076. www.ame.com IIIIIHENNIG perfect machine protection. Perfect Machine Protection. For...