Start from Battery Input: Single-phase 115 - 230 - 111 Vac Output Selectable Load:48Vdc 1.25A Output Battery charging:48 Vdc 1.25A Suited for the following battery types: Open Lead Acid, Sealed Lead Acid, lead Gel, Ni-Cd, Li-Ion Automatic diagnostic of battery status. Battery Life test function (internal Battery Impedance) Charging curve IUoU, constant voltage and current Four charging levels: Boost, Bulk, Trickle, Recovery Protected against short circuit and inverted polarity Signal output for: Battery Fault, Mains, Rectifier fail Ethernet: SNMP V3, Modbus TCP/IP, HTTPS DIN rail and Wall mount New revolutionary product, with Ethernet on Board provided with protocol connections: HTTPS, SNMPv3, Modbus TCP. The device also features the ADELBus protocol for connecting other ADELSystem devices. Power Management: Thanks to the All In One units (DC-UPS), it will be possible to optimize power management. The available power is automatically allocated between load and battery, supplying power to the load is the first priority of the unit thus it is not necessary to double the power, because also the power going to the battery will go to the load if the load so requires. The maximum available current on the load output is 3 times the value of the device rated current In. Climatic Data_ Ambient temperature (operation)_ Ambient temperature Storage_ General Data De-rating 5°C/1000m Auto convention Battery Care: it's the concept base on algorithms that implement rapid and automatic charging, four state of charge, battery charge optimization during time, flat batteries recovery and real time diagnostic during installation and operation. The Real Time Auto-diagnostic system, monitoring battery faults such as, battery Sulfated, elements in short circuit, accidental reverse polarity connection, disconnection of the battery, they can easily be detected and removed by help of Blink Code of Diagnosis Led; during the installation and after sell. The continuous monitoring of battery efficiency, reduces battery damage risk and allows a safe operation in permanent connection. Each device is suited for all battery types, by means of jumpers it is possible setting predefined curves for Open Lead Acid, Sealed Lead Acid, Gel, Ni-Cd(option). They are programmed for two charging levels, boost and trickle, but they can be changed to single charging level by the user. A rugged casing for DIN rail mounting, IP20 protection degree. They are extremely compact and cost effective. Interconnections: The platform communication for ADELSYSTEM devices, allows the connection of all components in a simple but very powerful way, Ethernet. A protocol communication based on MODbus TCP/IP or SNMP technology. You can select any of the two buses depending on the application. It allows to communicate with all the accessories provided by ADELSYSTEM and to develop an independent system for electrical continuity. At the same time, it allows monitoring and control all parameters in the system, even from the other side of the world, by means of application tools on the cloud. ADELSYSTEM allows you to implement very simple but sophisticated monitoring and control for your energy system and opens your mind to new ways to approach your applications. Norms and Certifications: The CE mark in conformity to EMC 2014/30/EU: Electromagnetic Compatibility Directive; 2014/35/EU: Low Voltage Directive; ROHS 2011/65/EU: Restriction of the use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS), as amended by 2015/863/EU. EMC Immunity: EN61000-6-2;EMC Emission: EN61000-6-3. According to: Electrical Equipment for Machinery EN 60204; Electrical safety (of information technology equipment) IEC/EN EN62368-1. Insulation voltage (input / ground)_1605 Vac Insulation voltage (Output / ground)_500 Vac_ Protection Class (EN/IEC 60529)_IP20_ Connection Terminal_IEC_ Protection class_M_ Input Data_ Nominal Input Voltage (2 x Vac)_ Input Voltage range (Vac)_ Input Inrush Current Limiter_ Inrush Current (Vn - In nom. Load) l2t AC Frequency_ Internal fuse (not replaceable)_ External Fuse (recommended) MCB curve B_ Input Current (No Load and Alarm) Input llOVac Functional Diagram Electronic power sharing Battery - Load General Output Data_ Turn-On delay after applying mains voltage Start up with Strong Load (capacitive load) Efficiency (at 50% of rated current)_ Ripple and Noise (20 MHz Bandwidth) Dissipation power load max (W)_ Start from Battery only, without main_ Short-circuit protection_ Over Load protection_ Over Voltage Output protection_ Overheating Thermal protection_ gH LEDFault System/Batt gH LEDMain or Backup : |-v Aux : |- Fault System/Battery : Main or Backup Load Output 48 Vdc (jumper selection)_ Output voltage (at ln)_44 - 57.6 Vdc (60.4 vdc Ni-cd) Continuous current (without battery) l|0ad= ln_1.25 A_ Continuous current ( With battery) l|0ad= ln+ Ibatt_2 x ln_ Max. Output Load (Main with Battery) l|0ad= ln+ lbatt(4sec.) 3 x ln max. (A)_ Max, current Output Load (Back Up)l|0ad(4sec.)_2 x ln max._ Output On/Off_Yes: Drive by Ethernet Push Button -Terminal Input "Start from Battery without main SrStf&SE. )i«onn«ct Protection Detect & Recharge Battery doted to aero V » Battery I Five Charging Mode: Recovery. Bulk. Abtorbtion. Boost, Float men, ,n y,oct Circuit Battery Cl Battery Tester 1Type battery Selection bead m iJ Temp. si/ Charging -©-Probe -' [-Rectifier Fail All specifications are subject to change without notice CBI6048A_21.docx

Time Buffering; (switch output off without main input) Battery Output_ Output Voltage Battery_ Boost-Fast charge Configuration 25°C (V/cell). Jumper Configuration battery type_ Float Charge Configuration 25°C (V/cell) Jumper Configuration battery type_ Min. Time Boost/Fast charge (Typ. at IN)_ Max. Time Bulk charge (Typ. at IN)_ Min. Time Bulk charge (Typ. At IN)_ Trickle Charge: Depend on Battery type (V cell)_ Ni-Cd: Trickle - Boos charging V/cell (20 cell)_ Recovery Charge_ End of charging Current (Bulk & Absorption charge) Charging current max lbatt_ Charging current limiting ladj_ Reverse...