CB12245AJ
1Pages

CB12245AJ Battery Charger One product for 12 and 24 Vdc field Battery Connection 12 or 24 V Battery Fault Free switch contact Charging for All Battery type Boost/Float Charge selection Input: 115–277 Vac CANBus connections Enabling Power Supply Select Battery: 12 or 24 V Charging current Limiting State of Charge Diagnosis Technical features Input: Single-phase 115 – 230 - 277 Vac Output Jumper Selectable: 12 Vdc 6A; 24 Vdc 5 A Power Supply Function: setting by Jumper Suited for the following battery types: Open Lead Acid, Sealed Lead Acid, lead Gel, Ni-Cd, Li-Ion (option) Battery Care for automatic diagnostic of battery status, short circuit element Charging curve IUoU, constant voltage and current Switching technology Semi-resonant Charging type: Boost, Absorption, Float, Recovery. Protected against short circuit, inverted polarity, over Load. Signal output (contact free) for fault battery state Protection degree IP20 - DIN rail CANBus J1939 Connection and Monitoring The CB series is a “Switching technology” and “Battery Care philosophy”, since years Signal Output (free switch contact) parts of the core know-how at ADEL system, led to the development of this advanced Main or Backup Input Power multi-stage battery charging method, completely automatic and suited to meet the most Low Battery advanced requirements of battery manufacturers. The Battery Care concept is based on Fault Battery algorithms that implement rapid and automatic charging, battery charge optimization Type of Signal Output Contact (free switch contact) during time, flat batteries recovery and real time diagnostic during installation and Max. current can be switched (EN60947.4.1): operation. The Real Time Auto-diagnostic system, monitoring battery faults such as, Max. DC1: 30 Vdc 1 A; AC1: 60 Vac 1A elements in short circuit, accidental reverse polarity connection, disconnection of the Min.1mA at 5 Vdc battery, they can easily be detected and removed by help of Blink Code of Diagnosis Led; Can (connection) during the installation and after sell. Each device is suited for all battery types, by means CanBus J1939 of jumpers it is possible setting predefined curves for Open Lead Acid, Sealed Lead Acid, General Data Gel, Ni-Cd and Li-ion. A rugged casing with bracket for DIN rail mounting. Insulation voltage (In /Out) Input Data Insulation voltage (In / PE) Nominal Input Voltage 115 – 230 – 277 Vac Insulation voltage (Out / PE) Input Voltage range 90 – 305 Vac Protection Class (EN/IEC 60529) Inrush Current (Vn and In Load) I2t  16 A  5 msec. Protection class Frequency 47 – 63 Hz 6% Reliability: MTBF IEC 61709 Input Current (115 – 270 Vac) 2.4 – 1.2 A Pollution Degree Environment Internal Fuse 4A Connection Terminal Blocks screw Type External Fuse (recommended) 10 A (MCB curve B) Dimensions (w-h-d) Battery Charger Output 24 Vdc (depend on jumper selection) Weight Recovery Charge 2 – 20 Vdc Safety Standard Approval Charging Current Max Ibatt < 40°C(In) Input V. 230Vac 5 A  5% Climatic Data Charging Current Max Ibatt < 40°C(In) Input V. 120Vac 4 A  5% Ambient temperature (operation) Charging Current Max Ibatt > 40°C(In) 3.5 A 5% De Rating Ta > 50°C Battery Charger Output 12 Vdc (depend on jumper selection) Ambient temperature Storage Recovery Charge 2 – 10 Vdc Humidity at 25 °C no condensation Charging Current Max Ibatt < 40°C (In) 6 A  5% Cooling Auto Derating Charging Current Max Ibatt > 40°C (In) 6 A  5% Yes No Yes Yes Yes Yes Generic Output Data Max.Time Bulk charge (Typ. at In) Min.Time Bulk charge (Typ. at In) Float Charge: Jumper Configuration battery type Float Charge Ni-Cd Float Charge Li-ion Fast Charge - Boost Charge (Lead Acid) Fast Charge - Boost Charge (Ni-Cd) Fast Charge - Boost Charge (Li-ion) End of charging current (Bulk & Absorption charge) Charging current limiting Iadj Quiescent Current Remote Charge Input Control Power Supply function Output Voltage 12 or 24 Vdc Selection Boost charge Enabling Efficiency (50% of In) Dissipation Power load max Residual Ripple Quiescent Current (No input main Voltage) Charging Curve automatic: IUoU Detection of element in short circuit Short-circuit protection Over Load protection Overheating Thermal Protection Over Voltage Output protection Resistive load Min. load Yes 3000 Vac 1605 Vac 500 Vac IP20 I, with PE connected > 300.000 h 2 2,5mm(24–14AWG) 45x110x105 mm 0.30 Kg approx. CE -25 ÷ +70°C - 2.5%(In) / °C -40 ÷ +85°C 95% to 25°C Auto Convection Yes Up to 50 °C Battery Tester Short circuit Element Detection Battery Impendency (Life test) Reverse polarity protection Battery Disconnected (Protection No Spark) Battery Voltage Wrong End of charge control 15 h 4 min. 2.23;2.25; 2.3; V/cell 1.2 V/cell 3.45 V/cell 2.4 V/cell 1.5 V/cell 3.65 V/cell 6% charging current 20 ÷ 100 % / In ≤5mA Bulk / Float By Jumper Enabling By Jumper Enabling By Jumper Enabling 90% 9W  60 mVpp  5mA /0mA Vbat<26.3 4 stage Yes Yes Yes Yes (Typ. 35Vdc) ADELView Graphic ADELView System Norms and Certifications Conforming to: Electrical safety, EMC directive 2014/30/UE, Low voltage directive 2014/35/UE, Safety EN IEC 62368-1, DIN41773 (Charging cycle), Emission: IEC 61000-63, Immunity: IEC 61000-6-2. CE Charging Type of charging it is Voltages and current stabilized IUoU. The state of charging battery and Auto-diagnosis of the systems are identified by a blinking code on a Diagnosis LED and Battery Fault LED: State LED Diagnosis LED Battery Fault Recovery 5 Blink/sec OFF Boost – Bulk 2 Blink/sec OFF Charging Type Absorption 1 Blink/sec OFF Float 1 Blink/2 sec OFF Reverse polarity ON 1Blink Battery No connect ON 2Blink Auto Diagnosis Element in Short C. ON 3Blink Replace Battery ON 5Blink