MODEL 1332 35 mm Hinges Included MODEL 1432 Hinges Purchased Separately Anti-Rak Cable System Flipper Door Slide® Up to 75 lb. [34 kg] Capacity 1332/1432 QUICK REFERENCE Door Sizes: Width: 10"- 26" Heights: 36"-78" Thickness: 3/4" min.-1 1/4" max. Lengths: 12"-28", 30", 32" Load: Maximum 75 lbs. per pair For vertical use only with Anti-Rak cable system Applications: Vertically mounted concealed doors for office/residential storage cabinets, entertainment centers, and armoires. Use model 1332/1432 with unique Anti-Rak cable system to eliminate door sag and wracking. This product is covered by U.S. (4,974,912) and various foreign patents issued and/or pending. Door Sizes Lengths Travel Slide standard in black zinc (CB) plating. Bright zinc (C) plating optional. Hinge base available in nickel plate only Widths: 10"-26" [254 mm-660 mm]. Door Heights: 36"-78" [914 mm-1981 mm]. Thickness: 3/4" [19 mm] minimum to 1 %" [32 mm] maximum thickness. When door thickness exceeds 13/16" [21 mm], use model 1432 with separately purchased 40 mm hinge. 12"-28", 30", 32" [303 mm-711 mm, 762 mm, 813 mm] See chart Load Hinge Hinge Carrier Strip Hardware Maximum 75 lbs. [34 kgs] per pair 35 mm cup; 94° self-close hinge included with 1332. Model 1432 shipped without hinge. Kits are ordered separately for all doors. For 2 doors 36"-56" [914 mm-1422 mm] tall, order 2 hinge carrier kits. For 2 doors 57"-78" [1448 mm-1981 mm] tall, order 3 kits. Slides, cables, and mounting screws provided. Hinge base is pre-mounted only on model 1332. Operating Envelope A 2"-2 ^" [50.8 mm-63.5 mm] “pocket” is required to clear the retracting door and the protruding hinge arms. Features Detent out, silenced open and closed. Optional part numbers in BOLD on chart indicate stocked lengths.

Choose Hinge Carrier Strip Kit The Accuride 4180 series hinge carrier strip kit accommodates door heights 36" to 78" tall. Based on door height select the number of hinge carrier strips required. Refer to chart below. NOTE: Refer to Page 7 for Component Part/Letter Cross Reference (i.e. J=Universal Screw). STEP 1 Secure Slides Inset Door Position slides as shown in Figure 1 against the floor and ceiling of the cabinet to self-align and maximize the leverage. Secure through the mounting slots using #8 X 7/16" universal J screws. The slides should be inset 1/8" [3.2 mm] behind rear face of door...

Installation Instructions 5. Tighten fixing screw and release slide plate. CAUTION: Do not cut excess cable yet! 6. In a similar manner, uncoil cable at lower slide and route it along the slide and around front side of pulley groove. See Figure 3. 7. Extend to back side of upper slide pulley. Pass cable around pulley groove and forward. Move upper slide plate to its most rearward position. Pulley 8. Wrap cable around upper adjuster block. With very light tension wrap cable around upper fixing screw. Tighten fixing screw. Ensure cable exits screw head near wall. See Figure 3. 9. Bring both slide...

STEP 4 Install Hinge Bases For model 1332: Hinge base already attached to slide in flush inset position (rearmost holes). See Figure 5. For model 1432: Select hinge brand and model. Install as shown in Figure 5 for flush inset applications. • See Page 6 for hinge manufacturers and part numbers by applications. Mounting with spacers (for hinges other than Salice). Place spacer(s) between the hinge base and slide plate. Secure with #8 x 5/8" hinge base screws (not provided). STEP 5 Bore Hinge Cup-35 mm-Model 1332 NOTE: ALWAYS bore a rough simulated door first to verify hinge cup locations. See...

Installation Instructions STEP 6 A ttaching Hinges A door notch may be required on doors 13/16" [20.6 mm] and t hicker. If so, notch door edge as shown in Figure 7. See tables on P age 6 for tab dimensions. Install hinges (included with Model 1332 o nly) on door using hinge screws provided. Hinge Adjustments A lternate Slide Mounting I n cases where the slides are not mounted flush with the floor and ceiling, use slide-to-hinge-cup relationship as shown in Figure 8. STEP 7 Install Door and Set Hinges • Clip hinges to bases. • With door installed and all recommended hinges connected, retract door...

Hinge Data 40 mm Thick Door Inset Overlay Amount 40 mm Overlay Salice CFA7A99 Base BAR3R09 Accuride Kit P/N 4180-0292-XE Requires 1 spacer, 3 mm (1/8"). For smaller door gap, increase tab. Notching may be required. Requires 3 mm (1/8") notch to the back of the door. Requires 2 spacers, 6 mm (1/4"). Will require hinge lateral adjustment to achieve door gap. May require notching. Cabinet Side Gap Tab 1-7/8" [47.6] Minimum Stile Width Door Clearance Open Position 5/16" [8.0] Reveal (3/4" Maximum Allowable Door Thickness) Requires 0 mm Base Optional Partition Closed Position Salice CFA7G99 Base BAR3R39...

Mounting Screws @ #8 x 3/8" Pan Head Zinc/Black • Attaches hinge carrier strip to the inner member • Attaches hinge carrier strips together without hinge base plate © #8 x 5/8" Flat Head Zinc • Attaches hinge carrier strips together with hinge base plate • Attaches base plate to hinge carrier strip © Qsbb> 2 each Hinge Carrier Strip-Black 3 each Connector Clip-Stainless Steel (Without Hinge Base Plate) Slide mounting kit includes black mounting screws and pivot blocks. Hinge mounting kit includes black Salice hinges, black hinge screws, and plastic hinge cover caps. Purchase black hinge...

Additional Hinge Kits Ordering Instructions To order additional hinge kits for inset doors, thick inset doors, or for overlay doors, see below for kit part numbers and contents. Complete your slide order for Accuride Anti-Rak Flipper Door Slide ® Model 1332 or 1432 by specifying the following: Model 1332 35 mm Hinge Kit for Inset Doors 3/4" to 13/16" [19.0 mm–20.6 mm] Thick Black Finish Part Number 4180-0407-XE 2 each 2 each 2 each 2 each 4 each 1 each Zinc Finish Part Number 4180-0389-XE 35 mm Salice Black/Zinc Clip-On Hinge 3 mm Mounting Base Plate 3 mm Hinge Base Spacer Accuride Logo Hinge...