Catalogs >
ABB Measurement & Analytics >
TEIP11-PS I/P signal converter for standard signals

TEIP11-PS I/P signal converter for standard signals
20Pages

Catalog excerpts

TEIP11-PS I/P signal converter for standard signals - 1

ABB MEASUREMENT & ANALYTICS | DATA SHEET TEIP11-PS I/P signal converter for standard signals

TEIP11-PS I/P signal converter for standard signals - 2

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E — Proven and reliable concept — Integral mount design • Small dimensions, low weight — Sturdy construction and solid functionality • Influence of shock and vibration < 1 % at 10 g — Variety of signal ranges • Input e.g. 0 to 20 mA or 4 to 20 mA • Output 0.2 to 1 bar (3 to 15 psi) — Complies with the following directives • EMC directive 2014/30/EU • EC directive for CE declaration of conformity — Wide temperature range • From –40° (optional –55°) to 85 °C (

Open the catalog to page 2

TEIP11-PS I/P signal converter for standard signals - 3

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Change from one to two columns — Concept The TEIP11-PS signal converter converts standard electrical signals, e.g. 4 to 20 mA to 0.2 to 1 bar (3 to 15 psi). It is therefore a connecting link between electrical/electronic and pneumatic systems. The signal conversion process is similar to the patented force balance method. Special features of the TEIP11-PS signal converter are its relatively small dimensions and outstanding operational stability when subject to shock and vibration. The converter can be subjected to...

Open the catalog to page 3

TEIP11-PS I/P signal converter for standard signals - 4

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E ... Designs Field mount housing The field mount housing is suited for installation on-site or in open areas. The housing can be made from plastic with IP rating IP 54, from aluminum with IP rating IP 65 and from stainless steel with IP rating IP 65. The housing is suited for wall mounting and for 2 in pipe mounting. A specially designed signal converter in a plastic housing unit enables the use of combustible gas as a power supply instead of the standard compressed air. Specification Input (electric) Signal range 0...

Open the catalog to page 4

TEIP11-PS I/P signal converter for standard signals - 5

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Transmission data and contributing factors Characteristic curve Linear, direct, or reverse action Characteristic curve deviation < 0.5 % Hysteresis < 0.3 % Dead band < 0.1 % Temperature < 1 % / 10 K within -20 to 85 °C (-4 to 185 °F) < 2 % / 10 K within -55 to -20 °C (-67 to -4 °F) Power supply < 0.3 % / 0.1 bar (1.5 psi) change in pressure Mechanical vibration < 1 % to 10 g and 20 to 80 Hz Seismic vibration Meets the requirements of DIN IEC 68-3-3 Class III for strong and strongest earthquakes. Mounting...

Open the catalog to page 5

TEIP11-PS I/P signal converter for standard signals - 6

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E ... Specification Design for rail mounting Material / IP rating IP 20 aluminum housing unit, with plastic cover Mounting Rail mounting: EN 50022 - 35 x 7.5 EN 50035 - G 32 EN 50045 - 15 x 5 Electrical connection 2-pole screw terminal for 2.5 mm2 (14 AWG) Pneumatic connection Vs NPT threaded hole for supply air and output Weight 0.25 kg (0.55 lb) Dimensions Refer to Dimensions on page 10. Design for block mounting Material / IP rating IP 20 aluminum housing unit, with plastic cover Mounting In block format with...

Open the catalog to page 6

TEIP11-PS I/P signal converter for standard signals - 7

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Design for field housing unit (aluminum/stainless steel) Material / IP rating IP 65 aluminum or stainless steel housing unit Surface Aluminum housing, painted with dual component coating, lower section, black, RAL 9005, screw-on cover, Pantone 420, stainless steel housing unit, electrolytically polished Mounting Wall or 2 in pipe mounting With stainless steel mounting bracket (accessory) Electrical connection 2-pole screw terminal for 2.5 mm2 (14 AWG) in the housing, screw connection NPT % in for the cable...

Open the catalog to page 7

TEIP11-PS I/P signal converter for standard signals - 8

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Ex relevant specificationsFlameproof (enclosure), ATEX ‘Ex d' Operation as intrinsically safe equipment Marking Type Examination Test Certificate Type Device class II 2G Ex d IIC T4/T5/T6 Gb DMT 02 ATEX E 121 X DOC. 900771 II 2G EN 60079-0: 2012 (General requirements) EN 60079-1: 2007 (Flameproof enclosure ‘d’) Marking Type Examination Test Certificate Type System bus, computer interfaces Device class Pneumatic data Supply pressure 1.4 bar (20 psi) / Temperature classes for the following versions: TEIP11 Doc....

Open the catalog to page 8

TEIP11-PS I/P signal converter for standard signals - 9

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Special conditions The I/P signal converter TEIP11-PS Doc. 901068 or TEIP11-PS Doc. 901069 must be set up outdoors as a pneumatic power supply when used with combustible gases. The supplied gas must be kept sufficiently free of air and oxygen to prevent a potentially explosive atmosphere from forming. The gas must always be routed to the outside. FM / CSA Intrinsically safe FM FM 'intrinsically safe' (not for metal field housing units) I.S.: CL I/Div 1/Grp A B C D FM 'intrinsically safe' (only for metal field...

Open the catalog to page 9

TEIP11-PS I/P signal converter for standard signals - 10

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E — Dimensions Design for control room housing unit for rail mounting Dimensions in mm (in) 5 Mounting bracket for DIN rail mounting 3 Output Figure 2: Dimensions of control room housing design for rail mounting

Open the catalog to page 10

TEIP11-PS I/P signal converter for standard signals - 11

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E Design for control room housing unit for block mounting Dimensions in mm (in) 5 End panel with central supply air connection 4 Electrical connections Figure 3: Dimensions of control room housing design for block mounting ** Version 0.4 to 1 bar (5.80 to 14.50 psi) *** Length 80 mm (3.15 in) per connection block

Open the catalog to page 11

TEIP11-PS I/P signal converter for standard signals - 12

TEIP11-PS I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-PS-EN REV. E — … Dimensions Design for plastic field housing unit Dimensions in mm (in) 2 Connection only with version for operation with flammable gas for diverting the escaping gas / 6 mm (0.24 in) screw terminal connection Figure 4: Dimensions of plastic field mount housing design

Open the catalog to page 12