*mydirectindustry

AI562

Product catalog summary

Ordering Data
The AI562 is an analog input module with 2 AI, RTD active inputs. It includes terminal blocks TA563-11, TA564-11, and TA565-11, each with 11 pins and different configurations. All components are in the active product life cycle phase, recommended for new installations.

Dimensions
Dimensions are provided in millimeters and inches.

Technical Data
The module operates at a rated process supply voltage of 24 VDC with a current consumption of 0.04 A. It features protection against reversed voltage and a recommended protection fuse. The module includes galvanic isolation and can handle a maximum surge voltage of 35 VDC for 0.5 seconds. It dissipates a maximum power of 1.1 W and weighs approximately 120 g. The module can be mounted horizontally or vertically, ensuring natural convection cooling is not obstructed.

Technical Data of the Analog Inputs
The module supports 2 configurable RTD inputs with a resolution of 0.1 °C/°F and 15 bits + sign for resistance. It supports Pt100, Pt1000, Ni100, and Ni1000 input ranges. The module update time is less than 1 second for all channels, with a typical analog to digital conversion time of 140 ms per channel. It includes overvoltage protection up to 30 VDC and supports a maximum cable length of 10 m for unshielded wire and 100 m for shielded wire.

System Data AC500-eCo
The module operates within a temperature range of 0 °C to +60 °C for horizontal mounting and 0 °C to +40 °C for vertical mounting. It supports a humidity level of up to 95% without condensation and operates at air pressures greater than 800 hPa. Creepage distances and clearances meet overvoltage category II, pollution degree 2 requirements.

Insulation Test Voltages
Various circuits are tested against other circuitry with voltages ranging from 500 V to 2500 V, depending on the circuit type, according to EN 61131-2 standards.

Electromagnetic Compatibility
The module is suitable for industrial applications and complies with IEC 61000-4 standards for immunity against electrostatic discharge, radiated interference, and transient interference voltages. It also meets IEC 55011 standards for radiation.

Mechanical Data
The module is mounted horizontally with a degree of protection of IP 20. It is classified as V-2 according to UL 94 and meets vibration resistance standards according to EN 61131-2.

Approvals and Certifications
Further information on approvals and certifications is available in the main catalog for PLC Automation.

Catalog excerpts

DATA SHEET 1 Ordering Data Part no. For planning and commissioning of new installations use modules in Active status only.

Open the catalog to page 1

Technical Data The dimensions are in mm and in brackets in inch. 3 Technical Data The System Data of AC500-eCo apply $ Chapter 4 “System Data AC500-eCo" on page 4 Only additional details are therefore documented below.

Open the catalog to page 2

Technical Data of the Analog Inputs Technical Data of the Analog Inputs NOTICE! Attention: All I/O channels (digital and analog) are protected against reverse polarity, reverse supply, short circuit and continuous overvoltage up to 30 VDC. 3.1 Technical Data of the Analog Inputs

Open the catalog to page 3

System Data AC500-eCo Environmental Conditions

Open the catalog to page 4

Insulation Test Voltages, Routine Test (NOTICE! Exceeding the maximum power supply voltage (> 30 VDC) for process or supply vol-• tages could lead to unrecoverable damage of the system. The system could be destroyed.

Open the catalog to page 5

Electromagnetic Compatibility

Open the catalog to page 6

Mechanical Data Mechanical Data 1) High requirement for shipping classes are achieved with additional specific measures (see specific documentation). 2) CM = Common Mode, DM = Differential Mode

Open the catalog to page 7

ABB Automation Products GmbH Eppelheimer Str. 82 69123 Heidelberg, Germany Telephone: +49 (0)6221 701 1444 Fax: +49 (0)6221 701 1382 E-mail: [email protected] abb.com/plc © Copyright 2017-2018 ABB. We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly forbidden.

Open the catalog to page 8

All ABB Automation Products GmbH catalogs and technical brochures

AI561
8 Pages
Automation Builder
12 Pages
AC500 as IoT Gateway
8 Pages
PLC Automation
264 Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list