Catalogs >
4B Braime Components >
IE-GuardFlex - distributed hazard monitoring system

IE-GuardFlex - distributed hazard monitoring system
1 / 2Pages

Catalog excerpts

IE-GuardFlex - distributed hazard monitoring system - 1

Product DATASHEET Datasheet PRODUCT IE-GuardFlex IE-GuardFlex Distributed Hazard Monitor System APPLICATION The IE-GuardFlex is the central control unit for 4B’s Distributed Hazard Monitoring Solution (DHMS). Using industrial Ethernet technology, the IE-GuardFlex controller connects to, and monitors multiple machine mounted sensors via our class leading IE-Nodes. The complete IE-GuardFlex system can be configured to support multiple machines, IE-Nodes and sensors, and will interface directly to the machine MCC’s to perform a controlled stop in the event of the detection of a hazardous condition. The IE-GuardFlex system is typically located within the plant MCC and dust hazard “safe area”. Connection is then made, via industrial Ethernet (CAT6 cabling) to IE-Nodes distributed locally to the monitored machines in the “hazardous area”. Typical machine types would be bucket elevators, enclosed conveyors, open conveyors, chain conveyors, roll stands, etc. The range of 4B hazard monitoring sensors are connected to the local IE-Nodes and monitor for hazardous conditions such as belt slip (SlipSwitch, Milli-Speed), belt misalignment (TouchSwitch, Bulldog), bearing temperature (ADB, Milli-Temp), Vibration (MilliVib), blocked chute (Binswitch), etc. With all IE-Nodes and sensors connected, the plant engineer can start the node search process using the intuitive GUI on the 7” colour touchscreen display. Found nodes can then be configured, and attached sensors allocated to user configured machines. The system allows for 3 stage ALARM / STOP configuration per sensor. Output relays can be assigned to ALARM and/or STOP conditions per sensor or per machine. In addition, the common ALARM and STOP output relays indicate if there is an alarm or stop condition present on any of the connected sensors. IP66 Stainless Steel enclosure ► 7” Colour touchscreen display with intuitive GUI ► Supports multiple machine configuration with the following inputs ► ► Run Signal (Input) Assignable ALARM or STOP relay (Output) ALARM and STOP relay x Configuration Options ► ► ► X4 = 4 x Speed Monitoring, 1 Alarm, 1 Stop X8 = 8 x Speed Monitoring, 1 Alarm, 1 Stop, 18 Relays X16 = 16 x Speed Monitoring, 1 Alarm, 1 Stop, 36 Relays 100 Machines 64 IE-Nodes 1024 Devices view and control over network access control ► Active alarm and alarm history ► Change log ► Multi-user Copyright © 2023 4B Group. All rights reserved. Information is subject to change or modification without notice. Refer to instruction manual for installation information. C

Open the catalog to page 1

IE-GuardFlex - distributed hazard monitoring system - 2

Product DATASHEET Datasheet PRODUCT IE-GuardFlex DIMENSIONS TECHNICAL SPECIFICATIONS Power Supply Ethernet Port 4 x RJ45 – for connection to IE-Node, IE-Switch, IE-Router ETH-CONT1V4-X4 = 4 x 24VDC run signal ETH-CONT1V4-X8 = 8 x 24VDC run signal ETH-CONT1V4-X16 = 16 x 24VDC run signal Output – Relay Assignable to sensor or machine ALARM or STOP condition ETH-CONT1V4-X4 = 0 – use common ALARM and STOP relay ETH-CONT1V4-X8 = 18 x Relay (2A at 30VDC) ETH-CONT1V4-X16 = 36 x Relay (2A at 30VDC) Common Output – Relay Housing Material Only required for machine speed monitoring Fixed output for...

Open the catalog to page 2