カタログ >
Yageo >
VRS series

VRS series
1 / 10ページ

カタログの抜粋

Innovative Service Around the Globe YAGEO DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CHIP VARISTORS VRS0402/0603 5.5 V TO 38 V RoHS compliant & Halogen Free

カタログの1ページ目を開く

Phfcomp_ Surface-Mount Ceramic MULTILAYER CHIP VARISTORS SCOPE This specification describes chip varistors with lead-free terminations. APPLICATIONS • Consumer electronic equipment • Telecommunications • Notebook • Electronic data processing FEATURES • Excellent clamping voltage • Excellent energy dissipation capability • Quick response time (<1n sec.) • Adjustable capacitance values • High reliability • High transient current capability • Symmetrical voltage-current characteristics ORDERING INFORMATION ° GLOBAL PART NUMBER, PHYCOMP CTC & 12NC All part numbers are identified by the series,...

カタログの2ページ目を開く

Phfcomp_Surface-Mount Ceramic MULTILAYER CHIP VARISTORS VR CONSTRUCTION Lead Free terminations, NiSn terminations Surface mount multilayer surge suppressor Very short response time (< 1.0 nsec) Bidirectional clamping Low capacitance for high frequency applications Very low leakage current Table 1 For outlines see fig. 2 TYPE L, (mm) W (mm) T (MM)

カタログの3ページ目を開く

Phfcomp_ Surface-Mount Ceramic MULTILAYER CHIP VARISTORS ELECTRICAL CHARACTERISTICS

カタログの4ページ目を開く

Phfcomp_ Surface-Mount Ceramic MULTILAYER CHIP VARISTORS ELECTRICAL CHARACTERISTICS STANDARD TESTING CONDITION

カタログの5ページ目を開く

Phfcomp_ Surface-Mount Ceramic MULTILAYER CHIP VARISTORS ESD (ELECTROSTATIC DISCHARGE) TEST ESD discharge circuit according to IEC 61000-4-2 SPECIFICATION OF ELECTROSTATIC DISCHARGE (ESD) TEST: According to standard EN 61000-4-2, up to 8 KV direct contact (contact discharge) THICKNESS CLASSES AND PACKING QUANTITY

カタログの6ページ目を開く

Product specification Surface-Mount Ceramic MULTILAYER CHIP VARISTORS METHOD OF MOUNTING For normal use the varistor may be mounted on printed-circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive in accordance with CECC 00802 classification A. For advised soldering profiles see Figs 4, 5, and 6. An improper combination of soldering, substrate and chip size can lead to a damaging of the component. The risk increases with the chip size and with temperature fluctuations (>100 °C). More detailed information...

カタログの7ページ目を開く

Product specification Surface-Mount Ceramic MULTILAYER CHIP VARISTORS Typical values (solid line) Process limits (dotted lines) The capacitors may be soldered twice in accordance with this method if desired Fig. 5 Double wave soldering Typical values (solid line) Process limits (dotted lines) Fig. 6 Vapour phase soldering

カタログの8ページ目を開く

Phfcomp_ Surface-Mount Ceramic MULTILAYER CHIP VARISTORS TESTS AND REQUIREMENTS Table 5 Test procedures and requirements TEST TEST METHOD PROCEDURE_ Bond Strength4.9 4.10 To be soldered on the glass-epoxy No visible damage of Plating on (thickness 1.6 mm), the load shall be put on End Face the board bends 1 mm Solderability 4.10 4.11 Unmounted chips completely immersed for The termination should be well tinned 2 ±0.5 seconds (dipping time) in a solder bath at 235 ±2 °C Resistance to4.10.2 4.12 Solder bath temperature: 260 ±5 °C | A V1mA / V1mA | <10% Soldering Heat...

カタログの9ページ目を開く