Turbine flow meter
1 / 13ページ

カタログの抜粋

XI'AN YUNYI INSTRUMENT COMPANY LIMITED 1.Pressure Transmi�er 4.Dead Weight Tester 7.Temperature Transmi�er 2.Pressure Guage 5. Level Transmi�er 8.Density Meter

カタログの1ページ目を開く

Liquid Turbine Flow Meter User Manual Warning When the ﬂow meter is installed at explosion hazard ﬁeld, DON’T remove the COVERPLATE when the meter is powered. Please make parameter se�ng at safe ﬁled prior to installa�on. Special No�ces Pictures & Descrip�ons are for your informa�on only, please refer to the actual product. Parameters are subjected to changes without no�ce. GENERAL INFORMATION This manual will assist you in installing, using and maintaining your turbine ﬂow meter. It is your responsibility to make that all operators have access to adequate instruc�ons about safe opera�ng...

カタログの2ページ目を開く

Measurable Flow Rate Range and Pres Level: (See table 1) Table 1. Measurable Flow Rage Range and Pressure Rating Standard - 304 Stainless Steel Optional - 316 Stainless Steel Tungsten Carbide Standard - 2Cr13 Stainless Steel (Optional Alloy CD4Mcu) 316 Stainless Steel Power Supply: Sensor: Transmitter: Field Display Type B: Field Display Type C: Accuracy: Standard: ±1% of reading; Wetted Components Housing: Bearings and Shaft: Rotor: Retaining Rings: Output Signal: (Where applicable) Sensor: Pulse signal (Low Level: <0.8V; High Level: >8V) Transmitter: 4 to 20 mA DC current signal Signal...

カタログの3ページ目を開く

Model Selection Nominal diameter(mm) Meter material Impeller material Explosion-proof grade CAUTIONS FOR INSTALLATION Mounting Positions Turbine flow meters should be installed at the place in compliance with the requirements below: •Easy maintenance •No vibration •No electromagnetic interface •Away from heat source Mounting Orientation All turbine flow meters are designed to measure flow in only one direction. The direction is indicated by the arrow on the body. Required Lengths of Straight Runs Flow altering device such as elbows, valves and reducers can affect accuracy. See diagram 1 for...

カタログの4ページ目を開く

See diagram 2 for straight pipe length requirement when there is altering device. Thread Connec�ons 1.To protect against leakage, seal all threads with an appropriate sealing compound. Make the sealing compound does not intrude into the ﬂow path. 2.Make the arrow on the outlet is pointed in the direc�on of theﬂow. 3.Tighten the turbine onto the ﬁ�ngs. Use a wrench only on wrenchﬂats. Flange Connec�ons For standard product, the ﬂange follows GB/T 9119-2000 (ISO 7005-1) RF (Raised Face). Note: ﬂange can be customized following other criteria. Use a gasket between the meter ﬂange and ma�ng...

カタログの5ページ目を開く

Notice: The straight section is included for DN4-DN10, but not DN15-DN Flange connection Wafer Connection

カタログの6ページ目を開く

Sanitary Connection

カタログの7ページ目を開く

•4.Function table for the Intelligent displaytype Warning: Electrical Hazard Disconnect power before beginning installation. Turbine Flow Sensor/Transmitter • 1. Pulse Type without Explosion Proof Terminal wiring Main Power Description of the symbols: + Default Function O Optional • 2. Pulse with Explosion Proof: Notice: l.The pulse means the signal which is in direct proportion to the impeller speed. 2.The scaled Pulse means the signal when the flow rate reach ONE unit volume( m3, L, 0.01L...) 3.The batter model is ER34615 4.The battery model is ER26500 Notice: (1) High level amplitude...

カタログの8ページ目を開く

Terminal Configuration Pulse / Scaled Pulse output Notice: The communication format is Modbus-RTU protocol 220Vac powered type Grounding Switch Terminal Configuration

カタログの9ページ目を開く

Terminal Configuration Pulse / Scaled Pulse output

カタログの10ページ目を開く

There are four keys: "Enter", "^", "t", "Esc". Description of Password Grade

カタログの11ページ目を開く

METER CONSTRUCTION Symptom Measurement is not accurate Probable Cause Solution 1. Turbine operated below minimum rate. Increase flow rate. Refer to Section 3.0 Operation Conditions Materials of Housing Stainless Steel 304 • Others available on request) Magnetic Pickup End Fittings: For hazardous areas, pickup colls supplied with explosion proof boss. Carbide Steel (Others available on request) 2. Turbine partially clogged with dried liquid Remove turbine. Clean carefully. Make rotor spins freely. 3. Installed too close to fiffings. Install correctly. Refer to Section 5.0 Cautions for...

カタログの12ページ目を開く

METER CONSTRUCTION Hereby provides a limited warranty against defects in materials and workmanship. This product includes a one-year warranty. The warranty period shall begin on the date of the original new equipment purchase. Warrantor's obliga�on hereunder shall be limited to repairing defec�ve workmanship or replacing or repairing any defec�ve parts. In the event Purchaser believes the product is defec�ve, the product must be returned to, transporta�on prepaid by Purchaser，within the appropriate warranty period rela�ve to the product. If 's inspec�on determines the workmanship or...

カタログの13ページ目を開く