High-Flow-Pleated Cartridges & Lenticular Cartridge Filters
1 / 13ページ

Filtersysteme It’s crystal clear. Filtersysteme Eine klare Sache.

High-Flow-Elements are filter cartridges which are provided with extremely high filter surface area and at the same time show a large cross section of its filtrate outlet. By the high filter surface area High-Flow-Elements can hold back a high amount of solids and by the large outlet cross section can be operated with high flow rates. High-FlowElements in each case need special High Flow-Pleated Cartridge Lenticular filters WFHFF High FlowPleated Cartridge, horizontal pleated CLC Lenticular filter cartridge Cellulose with special polymer binders High FlowPleated Cartridge with...

High-Flow-Pleated Cartridge, nominal, horizontal pleated High Flow-Pleated Cartridge, horizontal pleated WFHFF High-Flow-Pleated cartridges with diameter of 152mm and lengths from 20“ to 60“ are suitable for the very high flow rates. The internal filter structure is horizontal pleated and for all lengths continuously made from one piece of filter media with 97-99% retention efficiency. This creates a lot of space for high dirt hold capacity and long life time. High-Flow-Pleated Cartridges are available in the two adapter-configurations type P and type M, see picture below. The flow rate of type P...

Flow rate / Differential pressure* Length *Recommended flow rate at initial differential pressure < 0,1 bar: Efficiency (%) Filter Cartridge Adapter Configurations Type P: flow direction from inside to outside Adapter type P Type M: flow direction from outside to inside Adapter type M Order information WFHFF Adapter configuration P: Type P WFHFF-HighFlow-Pleated cartridge, horizontal pleated

High-Flow-Pleated Cartridge, absolute with Multi-Layer-Structure High Flow-Pleated Cartridge with Multi-Layer-Structure WFHFC High-Flow-Pleated cartridges with diameter of 152mm and lengths from 20“ to 60“ are suitable for the very high flow rates. The filter media which is framed in a stable 2-layered outer net out of polyester is pleated in Multi-Layerstructure and optionally manufactured out of polypropylene or glass fiber. The filter rations from 0.5 µm to 90µm show absolute filter efficiencies. The high filter surface area with depth filter effect creates a lot of space for high dirt hold...

Flow rate / Differential pressure* Length *Recommended flow rate at initial differential pressure < 0,1 bar: Efficiency (%) Filter Cartridge Adapter Configurations Type P: flow direction from inside to outside Adapter type P Type M: flow direction from outside to inside Adapter type M Order information WFHFF WFHFCHigh-FlowPleated Cartridge, with Multi-LayerStructure

Lenticular Cartridge Filters CLC Lenticular filter cartridge CLC Lenticular filter cartridges consist of cellulose with special polymer binders. Three types are available: the XE-filter layer with diatomite, the Proc3-filter layer with activated carbon and the W2-support layer used as alluvial filter for filter agents. The filter reaction of the applied XE-filter layer is due to the combined characteristics of the mechanical sieve-action of the filter medium as well as to the binding action of the impure substances resulting from the diatomite which it contains. CLC Lenticular filter cartridges are...

Filter ration XE lenticular filters *) Due to the retaining element of diatomite, the stated filter rations are to be used as a guide only. Order information Diameter Number of cells Filter layer Addition 12: 0 12" (300 mm) 16 = Standard XE: Cellulose with diatomite H: Wet-non-tear version _, _ Proc3: Cellulose with active carbon S: Protective felt, external Lenticular 16: 0 16" (400 mm> W2: Cellulose M: Fibre-retention felt, internal filter cart-

Lenticular Cartridge Filters WP Lenticular filter housings WP housings are used for the insertion of CLC Lenticular filter elements and are made of stainless steel AISI316L (1.4404). The housing fastening of the standard versions come with a v-clamp; the fastening can also be delivered with swinging bolt or bracket screw. The construction of the WP housings is optimal in regard to cleaning and sterilisation. In this respect the housing bolt can be lifted off the top and the separation of the dirt- and clean side takes place directly on the retaining plate of the filter element without an...

Spare parts Order designation Lower part Center post Sanitary vent Sanitary drainage

Dimensons Type

Order example Order information S = O-ring made of Silicone

Filtersysteme It’s crystal clear. Wolftechnik Filtersysteme GmbH & Co.KG Malmsheimer Straße 67 71263 Weil der Stadt Phone +49 (0) 7033-70 14-0 Fax +49 (0) 7033-70 14-20 E-Mail: info@wolftechnik.de www.wolftechnik.de/en