カタログ >
TOPWAY LCD >
HMT080ATA-C

HMT080ATA-C
1 / 33ページ

カタログの抜粋

HMT080ATA-C LCD Module User Manual Release Date - Preliminary Draft release -Add Highlight Description www.topwaydisplay.com www.topwaysz.com Document Name: HMT080ATA-C-Manual-Rev0.2.doc Page: 1 of 13

カタログの1ページ目を開く

LCD Module User Manual www.topwaydisplay.com www.topwaysz.com Document Name: HMT080ATA-C-Manual-Rev0.2.doc Page: 2 of 13

カタログの2ページ目を開く

LCD Module User Manual 1 Basic Specification TOPWAY HMT080ATA-C is a Smart TFT Module with 32bit MCU on board. Its graphics engine provides numbers of outstanding features. It supports TOPWAY TML 3.0 for preload and pre-design display interface that simplify the host operation and development time. Suitable for industry control, instrumentation, medical electronics, power electric equipment applications. General Specification Screen Size(Diagonal) : Resolution : Color Depth : Pixel Configuration : Display Mode : Viewing Direction : Outline Dimension : Active Area : Backlight : Command I/F:...

カタログの3ページ目を開く

LCD Module User Manual Terminal Function RS232 Interface Terminal (K1) Pin No. Pin Name I/O 1, 2 3 Descriptions Power supply (12.0V) Request To Send (could function as busy BUSY signal) (eg. to PC’s RS232C pin8 <9pin D-connector> ) Data output (eg. to PC’s RS232C pin2 <9pin D-connector>) Data Input (eg. to PC’s RS232C pin3 <9pin D-connector>) Ground, (0V) Note. *1. User data and commands transfer through this terminal. *2. HOST using command hand shake during communication is suggested. USB Interface Terminal (K2) Pin No. Pin Name I/O 1 2 3 4 5 Descriptions Power supply (5V) USB DATA...

カタログの4ページ目を開く

LCD Module User Manual GND=0V, VDD=12V, TOP =25C Items Symbol MIN. TYP. MAX. Unit Applicable Pin Operating Voltage VDD 10.5 12.0 13.5 V VDD Rx Input MARK(1) VRxM -3.0 -15.0 V Rx Rx Input SPACE(0) VRXS +3.0 +15.0 V Rx Tx Output MARK(1) VTXM -3.0 -15.0 V Tx Tx Output SPACE(0) VTXS +3.0 +15.0 V Tx RTS Output High VTXH -3.0 -15.0 V RTS(BUSY) RTS Output Low VTXL +3.0 +15.0 V RTS(BUSY) Operating Current IDD 205 mA VDD (*1) Operating Current (USB) IVUSB 160 mA VUSB Battery Supply current IBAT 6 uA (*2) Note. *1. Normal display condition. *2. For Battery driving RTC application, RTC configuration...

カタログの5ページ目を開く

LCD Module User Manual Basic Operation Function Descriptions TML files Picture files ICONS files UART interface Custom Memories Touch Panel Control and Draw Engine TML files, Picture files, ICON files are stored inside FLASH memory area. They are preloaded to HMT080ATA-C for stand alone interface use. Those files are preloaded via USB interface as an USB drive. All the interface flow and the touch response are based on the preloaded TML files VP variables memory is inside RAM area, it provides real time access via UART by the HOST or display onto the TFT by TML file. Custom Memories are...

カタログの6ページ目を開く

LCD Module User Manual Quick Start Guide Install TOPWAY Graphics Editor Import pictures 2. design UI flow Connect to host Show 5. real time data Command Descriptions Please refer to “SMART LCD Command Manual” . www.topwaydisplay.com www.topwaysz.com Document Name: HMT080ATA-C-Manual-Rev0.2.doc Page: 7 of 1

カタログの7ページ目を開く

LCD Module User Manual 5 Optical Characteristics Item View Angles Contrast Ratio Response Time TOFF White Blue Uniformity NTSC Luminance 1.IF= 40 mA, and the ambient temperature is 25℃. 2. The test systems refer to Note 1 and Note 2. www.topwaydisplay.com www.topwaysz.com

カタログの8ページ目を開く

LCD Module User Manual Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The brightness is the average value of 9 measured spots. Measurement equipment SR-3A (1° ) Measuring condition: - Measuring surroundings: Dark room - Measuring temperature: Ta=25℃. - Adjust operating voltage to get optimum contrast at the center of the display. Note 3: The definition of contrast ratio (Test LCM using SR-3A (1° )): Luminance When LCD is at “White” state Contrast = Ratio(CR) Luminance When LCD is at “Black” state (Contrast Ratio is measured in optimum common...

カタログの9ページ目を開く

LCD Module User Manual 6 LCD Module Design and Handling Precautions Please ensure V0, VCOM is adjustable, to enable LCD module get the best contrast ratio under different temperatures, view angles and positions. Normally display quality should be judged under the best contrast ratio within viewable area. Unexpected display pattern may com out under abnormal contrast ratio. Never operate the LCD module exceed the absolute maximum ratings. Never apply signal to the LCD module without power supply. Keep signal line as short as possible to reduce external noise interference. IC chip (e.g. TAB...

カタログの10ページ目を開く

LCD Module User Manual dropping from high place) will damage the LCD module. Protective film is attached on LCD screen. Be careful when peeling off this protective film, since static electricity may be generated. Polarizer on LCD gets scratched easily. If possible, do not remove LCD protective film until the last step of installation. When peeling off protective film from LCD, static charge may cause abnormal display pattern. The symptom is normal, and it will turn back to normal in a short while. LCD panel has sharp edges, please handle with care. Never attempt to disassemble or rework LCD...

カタログの11ページ目を開く

LCD Module User Manual 7.3 Additional Cover Lens Mounting (Figure 3) - For the case of additional cover Lens mounting, it is necessary to recheck with the CTP specification about the material and thickness to ensure the functionality. - It should keep a 0.2~0.3mm gap between the cover lens and the CTP surface.. - The cover lens window should be bigger than the active area of the CTP.It should be≥0.5mm each side. - It is recommended to provide an additional support bracket for backside support when necessary (e.g. slim type TFT module without mounding structure). They should only provide...

カタログの12ページ目を開く

LCD Module User Manual In general design, RTP V.A. should be bigger than the TFT V.A. and RTP A.A. should be bigger than the TFT A.A. (Figure 5) 通常设计时： RTP的可视区 V.A. 应不小于TFT 的可视区 V.A. 及RTP的动作区 A.A. 应不小于TFT 的动作区 A.A. (附图5) Warranty This product has been manufactured to our company’s specifications as a part for use in your company’s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in medical devices, nuclear power control equipment,...

カタログの13ページ目を開く

HMT080ATA-C 1 / 33ページ

カタログの抜粋

TOPWAY LCDのすべてのカタログと技術パンフレット

HMT080ATA-C
1 / 33ページ