カタログ >
TESTO/テストー >
Reference flue gas analyzer - testo 360

Reference flue gas analyzer - testo 360
1 / 12ページ

カタログの抜粋

Reference flue gas analyzer - testo 360 - 1

We measure it. Reference flue gas analyzer testo 360 – Portable reference analyzer for industrial flue gases O2 NO NO 2 NOx SO 2 CO 2 %H 2 O

カタログの1ページ目を開く

Reference flue gas analyzer - testo 360 - 2

Reference flue gas analyzer A notebook is required for the operation of the testo 360! • Accuracy fully compatible to stationary measurement • Tested for suitability for all systems according to TA-air, • Possible measurement parameters: 02, CO, NO, N02, C02 • Measurement of water content of the flue gas, flow velocity, differential pressure and temperature • Long-term stable sensor, no test gas necessary at measurement site • Integrated low-absorbtion Peltier measurement gas preparation (patemted) • Applicable under extreme ambient conditions Official emission measurements of industrial...

カタログの2ページ目を開く

Reference flue gas analyzer - testo 360 - 3

testo 360 system overview Telephone modem The testo 360 reference measuring system consists of an analyser unit, a notebook and the flue gas probe. All of the sensors (max. 7 gas sensors), the flue gas moisture measurement unit (optional), the measuring range extension unit (gas dilution, optional) velocity measurement (optional) as well as a low absorption gas preparation Peltier cooling unit are located in the analyser. The flue gas probe is connected to the heated hose with integrated filter: either the modular industrial probe or any non-Testo or special testo 360 is easily transported...

カタログの3ページ目を開く

Reference flue gas analyzer - testo 360 - 4

Technical data General measuring ranges In testo 360 the measuring range end value Is determined by the choice of test gases. Example: CO desired measuring range up to 300 ppm => test gas concentration approx. 240-260 ppm (approx. 80 % of measuring range end value). However, the recording of measurement values over the measuring range thus defined Is possible. Parameter Greatest measuring Greatest measuring range Permitted accuracy Accuracy achieved in the range with measuring range at 6 m gas path 11 test DIN 33962 11 1i All accuracies stated without the option „measurlng range extension"....

カタログの4ページ目を開く

Reference flue gas analyzer - testo 360 - 5

Technical data Technical data from suitability tests Suitable for the measurement of the parameters below In exhaust Time change during the maintenance Interval gas In systems according to Tl air, 13. BlmSchV (large furnace systems) and 17. BlmSchV (waste combustion systems). Smallest tested measuring range Zero point Reference point Maintenance interval: 14 days (In constant operation) Proof limit: (mean values, of display ranges) Influence of barometric air pressure changes on the measurement signal Permitted ambient temperature: Temperature dependency of zero point: Temperature...

カタログの5ページ目を開く

Reference flue gas analyzer - testo 360 - 6

Options / Software Information about Instrument upgrades and prices available on request.

カタログの6ページ目を開く

Reference flue gas analyzer - testo 360 - 7

Probe type Technical data Industry gas probes - modular system Heated handle, power supply 115 Power consumption: 200 watts; Temp, gas path: > 180 °C; Ready to operate: after approx. 20 min; Length of mains cable: 3 m; Protection class: IP54; Ambient temp.: -20 to +50 °C; gas inlet: G1/4"; gas outlet: M 10x1 outer thread; weight: niet G1/4, gas outlet M10x1 outer thread, weight 0.4 kg, ambient Ambient temp.: -20 to +50 °C; Protection class: IP54; Gas inlet: G1/4"; Gas outlet: M 10x1 outer thread; Weight: 0.4 kg Non-heated sampling pipe to +600 Non-heated sampling pipe to Non-heated sampling...

カタログの7ページ目を開く

Reference flue gas analyzer - testo 360 - 8

Transport and Protection Part no.

カタログの8ページ目を開く

Reference flue gas analyzer - testo 360 - 9

Temperature probes Probe type Probe shaft/probe shaft tip Measuring Accuracy Temperature probes Connection cable for temperature probes 0604 0194 Part no.

カタログの9ページ目を開く

Reference flue gas analyzer - testo 360 - 10

Pitot tubes Probe type Probe shaft/probe shaft tip Pitot tubes and accessories Connection cable for Pitot tubes Connection hose; silicone; 5 m long; max. load 700hPa (mbar)

カタログの10ページ目を開く

Reference flue gas analyzer - testo 360 - 11

testo 360: Typical Set for Official testo 360 flue gas analyzer, approved, without notebook, fitted with 02 gas sensor, gas preparation, housing heating Option C02 IR-sensor, Incl.absolute pressure measurement 0 to 5 Manual flow velocity measurement (deltaP measurement) with Pltot Basic software to operate testo 360 Hose heated, length 4 m Transport trolley Transport case Heated handle Heated sampling pipe Extension pipe to +600 °C, stainless steel 1.4571 Preliminary filter for dusty flue gases, ceramic Mounting flange, stainless steel 1.4571 Transport case for Industrial probes, aluminium...

カタログの11ページ目を開く